Jump to content
SAU Community

Recommended Posts

nice job tangles. looks good but it doesnt look that enclosed especially the other side not where the snorkel is but the other side cant water get in through there cause its not blocked off???

cheers Latin; going to chop up a piece of 25cm H x 100cm L heatinsulated foam, and form that around all areas of the cai to help block (however slightly) hot enginebay air - not concerned at all about water, cant see how much more than a droplet here or there can get in thru the front; never even considered that factor until you mentioned it lol

she'll be right :)

  • 3 weeks later...
  • Replies 94
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Dont mean to hijack this thread - but since its on the topic of pod filters I thought I'd post a question here.

Went to BT-revolution, motorware and re customs - all said that the type of Apex-i that I would be looking at woudl be the one that comes with the adapter etc. No one has the 022 Apex-i Pod that bolts straight on to the R33 series 2 skyline.

I know people have said on here, that we can just buy the pod and fit it in (unless i read it wrong), but it seems that the only ones that I can get my hands on are the ones with the adapters (so im looking at around $230 at the min).

Anyone want to clarify if this is right?

Dont mean to hijack this thread - but since its on the topic of pod filters I thought I'd post a question here.

Went to BT-revolution, motorware and re customs - all said that the type of Apex-i that I would be looking at woudl be the one that comes with the adapter etc. No one has the 022 Apex-i Pod that bolts straight on to the R33 series 2 skyline.

I know people have said on here, that we can just buy the pod and fit it in (unless i read it wrong), but it seems that the only ones that I can get my hands on are the ones with the adapters (so im looking at around $230 at the min).

Anyone want to clarify if this is right?

Buy it from eBay, install it yourself, and save yourself $$$

Make sure it is 500-A022

  • 1 month later...

I was going to post this if nobody else had, glad to see it appeared on page 1.

I'm never buying an HKS filter based on that, talk about woeful. I'm wondering how Unifilter compares as they make some pretty impressive filtration claims on their website (rather than going for peak power - that's easy just don't run a filter!).

Apexi's "lifetime use" basically means take it off every now and then and tap the dirt off it. Eventually you will want to replace it though, probably every couple of years when it starts looking ratty.

I'll be sticking with the standard airbox in my car.. probably standard paper filter too they aren't restrictive when they're clean so I'll just change it regularly!!

I was going to post this if nobody else had, glad to see it appeared on page 1.

I'm never buying an HKS filter based on that, talk about woeful. I'm wondering how Unifilter compares as they make some pretty impressive filtration claims on their website (rather than going for peak power - that's easy just don't run a filter!).

Apexi's "lifetime use" basically means take it off every now and then and tap the dirt off it. Eventually you will want to replace it though, probably every couple of years when it starts looking ratty.

I'll be sticking with the standard airbox in my car.. probably standard paper filter too they aren't restrictive when they're clean so I'll just change it regularly!!

Apexi makes panel filters too...

Wrong, the brand often determines the type. In the case of K&N and Finer they are oiled and therefore illegal in every state I have checked the allowances for replacement filters.

Testing of flow and cleaning ability points to the Apexi as the best available so ditch your pods, use the stock airbox with Apexi panel and some breathing mods and (for Victorians and others limited to no other mods when a larger IC is installed) and get a decent front mount and stay legal.

well realistically when are people buying things with legality in mind, nearly all modified skylines are defectable, unless your running ridiculous rpm and power, i doubt you are going to see much actual power at the wheels difference between the pod brands anyway

but if you want to waste the money, then go for it, tis only my input :)

Edited by knore

I am certain many don't want the hassle of being defected. I don't see a need to change for a number of reasons: I'm an Engineer and expect to be conducting vehicle modification inspections after I move to Brisbane so it helps to stay clean, keeping the standard box is an easy way to keep the heat off and protect your engine and turbo as it is easily modified to flow more air and look factory, not all filters are equal and some like HKS are just junk. Wanna buy some??

To what are you referring as wasting money? Pods, it depends on your ultimate power goals so they are probably the most available solution for tose people. If you only want about 270rwkw then a panel will handle it.

I have a k&n panel filter at the moment.

I want to keep it but I have just recently got a fmic installed and I want to figure out a way to keep using the stock box.

Because since I installed the fmic, the stock box intake pipe doesn't fit anymore.

Last thing I want to do is to buy a pod. Dont want to be defected.

Anyone can help?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...