Jump to content
SAU Community

Recommended Posts

  • Replies 173
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

My shift has been pushed back so now I can make it.

Except I was at the skidpan today, I let someone drive my car, and now my CEL is on (although the engine sounds OK and nothing is leaking).

:)

I'm going from a "no" to a "maybe".

anyone from Hornsby way heading to chatty - meet at mt colah maccas just before 8pm

:)

okbye

edit - a mate in a stagea might be coming too :D

Edited by evil_weevil
Should someone be calling up the pizza joint and at least asking for a "smallish" table either inside or outside to be setup and ready for us at 10:30pm?

Yea I'll do that, but does anyone know the phone no. of that place? lol... Nick? People living in the North Side?

Guys - i did a SEARCH :)

I think this is it?

Pizzeria e Cucina

315 Barrenjoey Rd Newport 2106 (02) 9986 0577

Or it may be

Lucky's Pep'e Pizza Bar

Shp2/ 303 Barrenjoey Rd Newport 2106 (02) 9979 1756

I think its the first one though :P

And yes - ill let you ring Vic :worship:

Hmm I called the first place and made an ass of myself LOL. It was the wrong place.. HAHA

Its actually

Lucky's Pep'e Pizza Bar

Shp2/ 303 Barrenjoey Rd Newport 2106 (02) 9979 1756

I left a message on their answering machine saying a few people (10-15) will be comming to eat there atound 10:30 and to make/leave room.

DO NOT WASH YOUR CARS! or THINK ABOUT WASHING YOUR CARS!

PLEASE! :P

I will hose it off, and have a half arsed effort at the rims, but thats it

If i have time ill take the rims off and run OEM rims :(

*walks off and grabs keys, straight off to car lovers*

:);):(

*goes with Stan*

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...