Jump to content
SAU Community

Recommended Posts

I was liking the lights to start with but want to get the red ones instead, like whats on Slims beast.

The dust is actually mud from going through some decent puddles on a couple of dirt tracks. :P

LOL!

Yeah Sl!ms looks very unique.

IMG_3308.jpg

Looks nice buddy!

Thanks Mate :P

I was up the coast in NSW this weekend visiting a mate... the car stands out there that's for sure lol..

I parked at my mates house and was away for the day.. when we got back home his neighbour came out to tell us that a few cars that had been driving by pulled over got out and started taking photos of the car haha

Looks like I may have a few fans :)

Looks nice man but those wheels look a whole lot better with no center caps!

Really? see i always thought they looked better with them, and i know i see alot without the caps. I'll have to take them off and see how i feel about it.

Really? see i always thought they looked better with them, and i know i see alot without the caps. I'll have to take them off and see how i feel about it.

Nice car dude :P , what sort of grill is that you've got ?

nice car, wheels look alright, what are they? look like a aussie brand, but not bad looking.

the wheels look awesome,put some pics of urs up

Looks tuff as, dont recon you could go much lower lol

thanks man i could probly go abit lower lol

Edited by Travis32
thanks man i could probly go abit lower lol

lol maybe just. do you have much trouble wih it at that height ?? as in bumps etc. or you normally have it higher ?

i have it at that height all the time.Just gotta go at angle n slowly over bumps etc.But yeh its low than i expected it to be but it doesnt worry me

its all good cops love me too.lol

they cant fit my licence standing up under the car lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...