Jump to content
SAU Community

Recommended Posts

Can anyone tell me the function of the extra-rich cold start?

i mean, my car idles crap and drives jerky (liek most r32's) when its cold, but is much better when its warm..

so i have been thinking...

what if i wire up the coolant temp circuit so that it always thinks its 'hot' and always gives me a nice idle?

is this bad for the engine in any way?

this is what i got from the rb20 workshop manual:

Cooltan temp sensor controls

- timing

- idle

At cold temperatures (20deg), the sensor gives the followign readings

- approx 3 volts

- 2.5 k ohms

At warm temperatures (80deg), the sensor gives

- approx 1 volt

- 0.3 k ohms

So... if i get a resistor that is 0.3 k ohms, cut the temp sensor off, and wire this resistor into the circuit so that it always reads 0.3 k ohms, will this make the car think its always warm? or does it use the voltage more than resistance?

cheers,

Warren

Edited by WazR32GTSt
Link to comment
https://www.sau.com.au/forums/topic/120724-cold-start-can-it-be-removed/
Share on other sites

yeah but the engine will warm up with cold start maps or normal maps

what does the cold start do that the normal map doesn't? richer?

so in actual fact it makes the car warm up even slower?

what else does it to?

just saying "don't do it because it has to be there for a reason" is not good enough for me

emmission control is there for a reason, but it is usually removed on cars when modified

the stock ecu is always tuned for emmisson control remember

I think the only down side is you will running rich all the time,

even when you car is warm up!

you will get really bad fuel comsumption!

because it doesnt know what temperature is your car at, and it keep send the same pulse, and that is how much fuel you going to get all the time!!!

Your car won't start on if you don't give it the cold start "rich" map. When the block is cold the fuel wants to turn to liquid (from a gaseous spray) on the cold metal eg. the bore. Therefore you need much more fuel present to make up for the fuel that is sitting as a liquid on the side of the bore and on the top of the pistons.

Also when the engine is cold you will notice the engine idles higher, this is to help get the oil circulating as quickly as possible and to help heat everything up.

A rich mixture does not stop the engine heating up as much as you would think. Remember the engine is only near on idling.

So basically forget about it. The car won't start easily at all and the engine once it does start will want to stall as well as it not being looked after while it is cold which is when you do most of the damage.

If you have a rough idle when its cold I would be looking at other things. I have seen r32's idle nicely cold so I would be looking at leads, spark plugs and coilpacks.

Hope that helps.

Edited by nfi
Your car won't start on if you don't give it the cold start "rich" map. When the block is cold the fuel wants to turn to liquid (from a gaseous spray) on the cold metal eg. the bore. Therefore you need much more fuel present to make up for the fuel that is sitting as a liquid on the side of the bore and on the top of the pistons.

Also when the engine is cold you will notice the engine idles higher, this is to help get the oil circulating as quickly as possible and to help heat everything up.

A rich mixture does not stop the engine heating up as much as you would think. Remember the engine is only near on idling.

So basically forget about it. The car won't start easily at all and the engine once it does start will want to stall as well as it not being looked after while it is cold which is when you do most of the damage.

If you have a rough idle when its cold I would be looking at other things. I have seen r32's idle nicely cold so I would be looking at leads, spark plugs and coilpacks.

Hope that helps.

i have tried changing many things from coils to plugs to filters etc

also... R32's dont have leads

I think the fuel maps are controlled by water temperature, not ambient air temperature...

I had a very rough idle after a PFC tune that leaned eveything out. By increasing the correction (adding more fuel) at low coolant temps I have smoothed the idle out.

Be careful - you may already be too lean at cold start. Could be fuel pump, clogged injectors etc.

If you get a PFC you can fiddle with things to see what works..but the standard maps should be fine - you either have a sensor or part that isn't doing its job..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...