Jump to content
SAU Community

Recommended Posts

  • Replies 102
  • Created
  • Last Reply

Top Posters In This Topic

Question for SK to get an Idea for the 2L boys.

Standard Rb20 with normal breathing mods - pod, intercooler, good exhaust, EBC etc.

What rpm does it start boosting?

What boost pressure have you found to be the most efficient to make power?

At that pressure, when does it hit max boost?

I understand that you probably feild questions like this all the time but I know that you run a GCG highflow on your rb20det and am very interested to hear your very knowledgable experience on the all round performance of this engine/turbo combo for a street car and what mods/tricks get the best out of this package?

Understand if you don't want to rewrite essays but any info would be most appreciated!

Keeping it as brief as I can;

Using a GCG Ball Bearing High flowed RB25DET turbo.

We used to run 1.3 bar on the old (170,00 k's) RB20DET for 225 rwkw

In 3rd gear it would make the full 1.3 bar by 3,750 rpm

(that's on the Commander and the Datalogit, the old R32GTST standard tacho read about 10% high)

It would hold the 1.3 bar all the way to 8,250 rpm (rev limiter)

Mods were a Power FC with boost control kit, POD, heat shield, ambient air feed, Jun adj cam pulleys (inlet and exhaust), Performance Metalcraft spilt dump, standard R32GTR intercooler, R32GTR fuel pump, R32GTR injectors and a light weight OS Giken twin plate clutch

Tuned for response, in particular we spent a lot of time tuning the ignition timing between 3,000 rpm and 6,000 rpm. Plus I sacrificed a little max power for more response using the adjustable camshaft pulleys.

I have compared a number of high flowed RB20DET turbos with RB25DET turbos and I can't say as I have noticed any difference in the external sizes of the compressor or turbine covers. The R34GTT turbine cover is slightly larger of course. My understanding is that the internal dimensions of the RB20DET turbine cover are slightly smaller than the RB25DET turbine cover. But that is machined to the same size when GCG do the high flow anyway.

:D cheers :(

Hey guys,

Would I have to retune the Power FC if I get this turbo?

Is there a difference between the rb25 turbo in the series 1 & 2 R33?

I have a series 2 turbo on my RB20 so it would be a straight swap right?

Hey guys,

1. Would I have to retune the Power FC if I get this turbo?

2. Is there a difference between the rb25 turbo in the series 1 & 2 R33?

3. I have a series 2 turbo on my RB20 so it would be a straight swap right?

Suggestions follow;

1. Yep

2. Not after it's high flowed

3.Yep

:) cheers :dry:

Edited by Sydneykid

Hey Gary

If you ever have anyone looking to high flow an r34 turbo (with the larger rear housing), but the turbo is still on their car and they want to do the swap on and off in one day, I have a blown one.

I'd be willing to let them have that highflowed in exchange for a working on. They'll get the same result anyways :)

  • 2 weeks later...

Hey Gary. Did you have a dyno sheet you could put up for your R32 setup?

If I had the supporting mods with an ECU remap and a JayCar boost controller instead of the PFC and associated boost controller would I theoretically achieve similar results?

Cheers in advance

EDIT: did you have cams with the adj. cam pulleys?

Edited by ellie
Hey Gary. Did you have a dyno sheet you could put up for your R32 setup?

If I had the supporting mods with an ECU remap and a JayCar boost controller instead of the PFC and associated boost controller would I theoretically achieve similar results?

Cheers in advance

EDIT: did you have cams with the adj. cam pulleys?

Sorry, I don't have a dyno sheet that I can post up for the R32GTST with the RB20DET in it.

There are limits to the ECU remapping, you might run into them before you get to the target power output. Every car is different, I can't be more specific than that.

Cams is an interesting story, I was given what I was told where standard R32GTR cams. I had no reason to check them. There wasn't any reason for me not to believe the guy that gave them to me as he had no motive to do otherwise. I stuck them in at the same time as I did the turbo and the Power FC install. Tuned it and away we went, used the old RB20 for couple of years. Then I stuck the original RB30DET into the R32GTST and gave the cams back to the guy that loaned them to me. It wasn't until I tried to copy the R32GTR cams into RB20 trick for someone else that I ran into problems, same as a few other guys have.

So I don't know whether it made the power on standard RB20 cams, RB20 aftermarket cams, standard RB26 cams or maybe even aftermarket RB26 cams. When I sold the original RB30, I stuck the RB20 back into the R32GTST with its original cams. It made within 8 rwkw of the same power, which I wasn't surprised at given its age, it was getting pretty tired at 180,000k's and after 3 years of racing.

Not a very conclusive answer I know.

:D cheers :D

Hey Gary. Did you have a dyno sheet you could put up for your R32 setup?

If I had the supporting mods with an ECU remap and a JayCar boost controller instead of the PFC and associated boost controller would I theoretically achieve similar results?

Cheers in advance

EDIT: did you have cams with the adj. cam pulleys?

You will find it very very difficult to get full boost (1bar or more?) on before 4k as Sk has, however 300rwhp can be achieved with standard cams and no cam gears, with these items you can bring boost on earlier (more cams..) and gain more hp obviously too! I am going to go down the cam's track abit later for some more responce but have no idea on what cams to use as i havn't look at that yet

Edited by jazza08

hey do you know if you can purchase the internals or rebuild kit from gcg and then rebuild the turbo yourself? I've pulled apart a saab turbo before and re-assembled it. wasnt really that hard

hey do you know if you can purchase the internals or rebuild kit from gcg and then rebuild the turbo yourself? I've pulled apart a saab turbo before and re-assembled it. wasnt really that hard

My understanding is the rotating assembly, once mounted in the core, needs to be balanced on a fairly expensive (and highly accurate considering 150,000 rpm ) piece of machinery. From there on it’s a simple bolt on job for the compressor and turbine covers which have been machined to match the compressor and turbine. So not much time (money) to be saved as their is very little DIY.

:P cheers :(

well worth your money alphinestar? i noticed in your signiture youv got heaps done to your car but 261rwhp isnt a whole lot? i dont understand.

I was wondering if this group buy is still available. I think today I blew the turbo, I was driving along gassed it then heard a loud pop followed by a big cloud of white smoke and no boost, a mate thinks it may not be the turbo but engine related. my guess is Ive over boosted. recorded 1 bar on the ebc .

sk,

When are you going to be running a GB for the R34 Neo Turbo's? as i have a blown r34 turbo that i want to get highflowed instead of my r33 one!

Cheers

Send me the R34GTT turbo and it will be done. PM sent.

:happy: Cheers :)

well worth your money alphinestar? i noticed in your signiture youv got heaps done to your car but 261rwhp isnt a whole lot? i dont understand.

261rwhp was with my old turbo with blown seal

ill give an update on thursday when i get the retune hope i can get 300 with stock injectors

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...