Jump to content
SAU Community

Recommended Posts

Just wanted to ask if i should drive my car around because i need some quotes from panel beaters.

The question that i wanted to ask is about that little fan in front of the radiator.

Mine isnt working... most likely due to the car accident.

Curious if i should be driving it without that working.

I left it on idle for about 1/2 hr to see how it goes and it was fine.

The rest of the car is fine just really some body damage but they are fixable.

Also can any panel beater be able to fix my car or are there some people that i have to go to?

Just wondering...

Thanks

Link to comment
https://www.sau.com.au/forums/topic/121889-should-i-drive-the-car/
Share on other sites

One little tip as I've learnt the hard way.

Attempt to avoid the pump shops.

Take the car to enthuaist crash shops/spray painters.

Look for nice cars in the parking lot not commodores/falcoons.

If there's no leaks and everything looks ok drive it and get quotes.

I'm assuming its under insurance?

yea i would like to take it to a smash repair place that has done imported cars before... just dont know where to take it to around Penrith, Sydney area.

Yea i wish it was under insurance... guess i learned my lesson

your car should be ok with the temps the way they are, however dont go for long trips of highway driving and try not to get stuck in traffic. if you are getting it fixed on insurance ask the insurance company who they use and get quotes from them, also look for a place that gives you a warrenty on their work

long trips on highway would keep the engine cooler then long trips in traffic. if you can keep the car above 50km/h as much as possible then it should not over heat in the cool temps we got atm.

Just make sure the temp gauge does not get anywhere near the top. Should be ok to drive unless its very hot and your driving in traffic for longer then 20 mins.

Edited by Guilt-Toy

The little fan in front of the radiator is only for the air con and when the water temp gets up to 95 degrees or so.

So driving it around on a winters day with the heater on rather than the aircon isn't going to cause problems.

Unless you have removed the factory viscous fan.......:)

  • 2 weeks later...

Yea just realised the little fan in front of the radiator must be the aircon fan... that shouldnt be a problem.

Also got a ridiculous quote from Emu Plains Smash Repairs.

They said that the body will cost me about under $6000. I think thats a pretty ripoff quote.

Here are the main things that got damaged from the accident. Besides this all ive got to worry about is that rear right wheel on a slight angle.

Do you think this will cost me $6000?

post-27024-1150800966.jpg

post-27024-1150801008.jpg

Yeah 6k sounds a bout right, theres alot of bits that need to be replaced; bumpers, guard, rear light, it all adds up. You did a good job on the quarter! even if it was pulled out or replaced either way thats the most expensive task.

Yeah $6k sounds reasonable. Don't forget they've gotta paint a fair amount too, but the rear quarters are a fair bit of work. Unfortunately not as simple as just bolting on a new panel. Still definately shop around though, but remember you get what you pay for. I've seen this is specifically the case when it comes to body repairs...

Yea just curious about my right rear back wheel.

Since its on a slight angle... just looking for a figure here.

How much is it to replace the whole suspension? If its even got anything to do with suspension?

If to repair the damages of that back wheel costs as close to $2000 then I might as well buy the whole suspension kit from Sydneykid

Call a wrecker and ask what a complete rear subframe is worth minus the diff or just replace what is bent. ;)

Sydneykids suspension kit is simply shocks and springs, bushes etc.

The reason your wheel will be bunged out is possibly a bent suspension arm of some sort.

Oh really... Guess my car wont be on the road for a while.

Looks like ive just gotta save at the moment.

A complete rear subframe... they dont come very cheap do they?

I'll try that out... I'll give a wrecker a ring.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...