Jump to content
SAU Community

Recommended Posts

hey

my car is a series 1 r33 gts25t. Lately my turbo has been making a very faint whining noise every every now and then. This happens between -30cmHg and -20cmHg (read out on blitz dual sbc spec s). This is the only time i hear this noise (under very light throttle), never when making positive boost or under hard/harder acceleration.

Is my turbo on the way out? Or is a maybe a slight leak somewhere, or possibly something else?

I've searched some other posts and people say they get a squeal/whine noise when making boost at say 3500rpm, yet i get a faint whine at about 1800rpm, so i'm not too sure...

Link to comment
https://www.sau.com.au/forums/topic/123089-is-my-stock-turbo-dying/
Share on other sites

no, it doesn't blow any smoke (looked for that, and have also looked for any oil coming out of the turbo or piping and there is none).

the car has done about 104000km (assuming if it has been wound back, then more than this figure). It is a 93 model.

boost is stock and a setting at 10-11psi. But before the ebc (about 1 and 1/2 yrs ago) who knows what it could have spiked to during the period after the exhaust was fitted, as all i had to go by was the stock boost gauge.

mine does the same on slight acceleration - changed oil regularly and all seems fine tho - still makes slight whine (like a dog whistle almost) which I've heard on lots of others - bear in mind this turbo is spooling up to the phenomenal speeds it spins at just before the actuator opens so on slight accel your gonna hear something spin up - I haven't heard a totally silent one yet myself but I'm no expert either so every skyline I've driven or drove in might have been knackered lol!

the slight noise you could be hearing could be air passing through the bov. there is a point where you can hold the throttle where the bov will be open slightly. and since there is air permanently leaking around the bov through a recirculation hole, it can cause a whistle.

hey mad082 - you mention a bov (I'm assuming thats a blow off valve heh!) - do all r33gtst's have them or are they aftermarket addition?

I only ask as mine too makes this subtle whistle and it is at a certain point on the throttle as you said but I dont have an aftermarket dump valve on my car :D

theres other signs that your turbo is going anyhow - small puddles of oil in that metal piping that feeds up from your intercooler. There can be slight smears in the pipe that you can wipe of with your finger (charge pipe is it?) so dont fret if you pull it off and see that but if you pull if off and see it dripping then I'd be a bit more worried :D

smoke out the back on hard boost - basically oil escaping I think.

only know this as I had to disconnect mine getting to the spark plugs and we checked this area recently

all 33's came stock with a blow off valve... although the correct name is compressor bypass valve. it is situated just before the throttle body, on the cabin side of the piping. the are hooked back up to the intake between the air filter and the turbo, so that when you lift off the throttle the air goes back through the turbo to keep it spinning (like blowing on a kids windmill that you get from fair).

also i had oil dripping out of my intercooler piping at the throttle body, and a small amount through the piping before i did my frount mount. I thought it might've been the turbo on the way out, but after a few weeks with the front mount i pulled one of the new pipes off and there was no trace of oil at all. it turns out that the stock front seal on the turbo will always leak a tiny amount of oil. the front seal is like a piston ring. it isn't a full circle. it has a slight gap in it.

so my problem was just old oil, and a bit of blow by.

Edited by mad082

thanks guys. I will get the car on a hoist and a have a good look to check for tiny leaks in intercooler piping, as well as make sure the bolts on the tubo aren't loose.

Didn't think of the that tiny air recircualtion hole in stock bov, could be that.

Cheers...

Don't discount the bearings.

Mine had that whine on boost, it was on and off, and didn't really effect the performance.

I did a track day at Winton, all was good, but on the video, I coul hear it whining. high pitched noise.

A week later the bearings shat themselves.

So I got a high flow.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't think the shuffle can damage the turbos. It only happens at low shaft speeds and loads. It's just annoying (to some people - others are tickled by the effect) and it quite possibly reduces spool performance a little bit.
    • Oh dear. The panel beating needs to be done before the filler work. Do you have a photo of the dent before you started? Hard enough to not flex and only hit the high spots?  What do you mean it was just temporary? 
    • Can u check this way it works for power supply?
    • These coils draw 10amps that what i read online
    • I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
×
×
  • Create New...