Jump to content
SAU Community

Recommended Posts

Guys,

I may have the option to buy the r33 widebodykit and was wanting to know peoples thoughts on this kit and also if anyone has this kit fitted if they are suppose to go on gtst's or gtrs or both in the way of fitment and alignment wiht bolt holes etc

regards

Mushroom

Link to comment
https://www.sau.com.au/forums/topic/123805-kakimoto-bodykit/
Share on other sites

we've got the original as the company track car... built by kakimoto (not the copy by skyline imports)... the kit's meant for a GTSt, but can be adapted onto a GTR.

The original uses rear castor to make the wheelbase of the car longer than standard (for race use). The copy was remoulded so the wheels could sit in the factory position without rubbing on the kit.

You'll need 10.5" wide rims for the front and 13" wide for the rears to fill out the guards.

Expect to pay about 5k for having the kit fitted, as if you want to have it done properly you'll need to modify the body so the wheels don't rub, and have the inner guard cut etc. Also blending the rear fender skins into the body requires you to take the original body back to metal, and bonding the fibreglass to it, or risk having it crack in the heat with age.

here's ours...

60898502.decamayweb06DecaMayLongWangaction23.jpg

To my knowledge none of the skyline imports built ones have the Kakimoto wing (which everyone thinks is rice, until you actually sit in the car and realise that you can't see the wing through the back, and is fully adjustable carbon). There's also a carbon splitter for the front, which we've removed because it seems to collect everything on the ground. Also Kakimoto seems to refuse to sell the widebody sized rims to the public, unless you actually have the kit fitted by them.

There still trying to off load that kit eh. Funny what happen's when you ring Mr kakimoto him self, and he makes legal threats to dodgy people about having his kit knocked off.

Nice kit how ever, if you buy it make sure you don’t go cheap on the wheels, it’s what make the kit look complete.

Edited by Nismo_Boy
355.... OMG Ubbbbberrrrrr rubber...

I wonder and shudder as to the cost of name brand tyres... :)

We run Pirelli P-Zero's. $800 a pop

AFAIK there's R32 and R33 kaki widebody kits, but not R34 from memory.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...