Jump to content
SAU Community

Help Window Has Fallen Into The Door

stingray
 Share

Recommended Posts

stingray Collaborator

stingray

Posted
Posted

My window on the R32 fell down inside the door and now won't wind back up. Just when I closed it today it made a lound clunk noise and I went to open it again. That's when it just slid down. It doesn't sound like it's rattling or anything so I don't know if it's fallen of its tracks or something else. I will be taking the door apart tomorrow and removing the sound deadening to have a look. I just want to know what the general problem could be as I don't really know how the window mechanism operates.

stingray Collaborator

stingray

Posted
  • Author
Posted

Anyone know how to remove the assembly. I've taken the 4 bolts of and tried lifting the whole thing out including the window, but there's not enough clearance at the top for it to come out. Do I need to remove the window first? I've attacted a picture of the 4 botls that I took off.

post-3291-1152070276.jpg

  • 4 years later...
bozodos Grand Master

bozodos

Posted
Posted (edited)

on another note, does anyone know if it's possible to get the window to go back up and stay up? (given that it will probably take at least 2 days to get a new assembly sent here if it's the cause)

Edited by bozodos
.:: GimpS-R34 ::. Grand Master

.:: GimpS-R34 ::.

Posted
Posted

pillars.. maybe to the roof.. unless you wanted to jam a block underneath? maybe more difficult though.. Just do the bogan thing.. plastic and tape around the outside..

  • 2 weeks later...
bozodos Grand Master

bozodos

Posted
Posted

FFS. new assembly has arrived, and went in fine, however I was foolishly trying to do the locating nuts up as tight as they were beforehand and one snapped off. The other snapped off taking it off.

Low quality pics show what I mean here, the red circle is the head of the nut which has snapped off. Is it possible to get these re threaded in some way or am I just going to have to get a new window. fml

09272010024.jpg

09272010025.jpg

.:: GimpS-R34 ::. Grand Master

.:: GimpS-R34 ::.

Posted
Posted

1. You have a red square, and blue circles.. i am going to assume the red square (not circle) is the head of the bolt/threaded bar and the blue circles are where they snapped..

what is on the other side of the threaded bar, or did you screw the threaded bar in? if so i would look at drilling a hole in the middle of the threaded bar and using a screw extractor kit to get it out and replace it..

is that what you are looking to do? pics are pretty bad..

bozodos Grand Master

bozodos

Posted
Posted (edited)

pretty much, and yeah after i'd uploaded them to my computer noticed that i had gunk on my phone camera lens.

there is a flat side like a rivet on the other side of the threads, going to look at just getting another window before the thread replacement option. my inital reaction was FFFFUUUUUUUUUUUUUUUUU. I figured that I am probably not the first person to do this, but wasn't sure if it was one of those kind of things which are set into the glass at the factory while it is still hot etc. My failure was in attempting to tighten them up to the point as they were when I took the window out.

Spose that will teach me to tighten things up too fkn much.

Edited by bozodos

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 Gtst - Track Car

      By Duncan · Posted

      Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • Dose Pipe Sutututu
      R32 Gtst - Track Car

      By Dose Pipe Sutututu · Posted

      https://www.facebook.com/share/p/18rmVb1SKB/ 
    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • No Crust Racing
      R32 Gtst - Track Car

      By No Crust Racing · Posted

      Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...