Jump to content
SAU Community

Recommended Posts

Fate has forced my hand! The R32 just blew its turbo so R33 wheel studs need to be fixed so I can drive it while the R32 gets its upgrades done!

Does anyone have any useful advice for me on how to do this?? Or does anyone want to come and help me do it on Saturday afternoon? Rewards of course will be offered for the helpers :D Thanks guys

Link to comment
https://www.sau.com.au/forums/topic/125048-stripped-wheel-studs-on-my-r33/
Share on other sites

1. Take wheel off

2. Take caliper off disc

3. take disc off

4. get big hammer

5. belt old stud out

6. slide new stud in from behind

7. use old stripped stud as a punch to push new stud in (or alternatively get a rattle gun and do up a wheel nut onto the new stud to pull it through)

8. put disc back on

9. put caliper back on disc

10. put wheel back on

11. ????

12. Profit

Where do I buy the new studs from??

Jason there is alcoholic rewards if you come help me :D

try repco they will normally have a range of wheel studs...

i got mine from option1garage over @ hamilton (although i have slightly longer ones 70mm i think)

make sure you get ones with the correct spline, as you'll have a mission of a time bashing them in, or drilling bigger holes etc...

the rattle gun method Azzura mentioned is good, just make sure you dont over tighten and end up ruining your thread as a fair bit of heat is generated. a rubber mallet is also handy - dont know when i used it but i know i used it heaps. after you've replaced the studs remember to periodically tighten up your bolt nuts as they settle in.

not a big job, just time consuming ;)

good luck

try repco they will normally have a range of wheel studs...

i got mine from option1garage over @ hamilton (although i have slightly longer ones 70mm i think)

make sure you get ones with the correct spline, as you'll have a mission of a time bashing them in, or drilling bigger holes etc...

the rattle gun method Azzura mentioned is good, just make sure you dont over tighten and end up ruining your thread as a fair bit of heat is generated. a rubber mallet is also handy - dont know when i used it but i know i used it heaps. after you've replaced the studs remember to periodically tighten up your bolt nuts as they settle in.

not a big job, just time consuming ;)

good luck

Yeah don't try to put a front stud in the rear hub, and waste two hours of your time before you realise that they are actually different!!! Like I did at the track day!! :D

Studs are only about $5 each... Once you know how its pretty easy - like anything I guess.

You dont HAVE to use a rattle gun, but it makes it much easier.. You will have to pack the wheels stud up with washers or a big nut so that you can wind the nut onto the stud without running out of thread on the nut. I hope that makes sense?

i'm happy to help out Andy.

I got my wheel stud from Nissan, as they are the same as R32 GTR ones.

was cheap as chips... think it was like $7 or something

don't know if they'd have R33 ones though, or if they're the same etc (though one would assume they would be?)

Yeah don't try to put a front stud in the rear hub, and waste two hours of your time before you realise that they are actually different!!! Like I did at the track day!! :D

Oh dears! I was wondering what you were gonna do! I felt so bad for ya too, you were having an awesome run!

Hey Andy,

You got my number, gimmie a call if you need a hand. I am but 5 mins from your house.

Thanks mate ;)

Yeah don't try to put a front stud in the rear hub, and waste two hours of your time before you realise that they are actually different!!! Like I did at the track day!! :D

Studs are only about $5 each... Once you know how its pretty easy - like anything I guess.

You dont HAVE to use a rattle gun, but it makes it much easier.. You will have to pack the wheels stud up with washers or a big nut so that you can wind the nut onto the stud without running out of thread on the nut. I hope that makes sense?

I should have watched you fix that!! By the way....Watching your car on the track got my mouth watering, gave me a preview of my engines future :)

i'm happy to help out Andy.

I got my wheel stud from Nissan, as they are the same as R32 GTR ones.

was cheap as chips... think it was like $7 or something

don't know if they'd have R33 ones though, or if they're the same etc (though one would assume they would be?)

Thanks mate! ill give you a call later in the week??

I should have watched you fix that!! By the way....Watching your car on the track got my mouth watering, gave me a preview of my engines future :D

Hehe yeah, if only you were psychic and knew you were going to need to know how to do it! ;)

I can promise that you wont be disappointed with the turbo! :)

Hehe yeah, if only you were psychic and knew you were going to need to know how to do it! :D

I can promise that you wont be disappointed with the turbo! ;)

I knew at the time that it needed doing...I just didnt know that is what you were up too!!!!

we can have "comparisons" at EC in October Woooooot

if you need to know details of the studs that are required check out the www.niceproducts.com.au website - all the info you need is there

I am having mine replaced, but the biggest problem has been finding wheel nuts to suit my mags ..

A workshop told me it's only a 20 minute job to preplace all studs to both rear wheels .. sounds like the easy option to me

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...