Jump to content
SAU Community

Recommended Posts

Hey guys, used 3/4 of my lunch searching for an answer so im just gona ask,

got a problem, s2 r33, stock ecu and boost control, once over 4000 rev's the car begins to hesitate and it feels as if its loosing power, i.e. it just pull like the 5psi below 4000 is pulling hrder..... where should i begin the look.

possibilities ?

im no mechanic but i can pull stuff apart... famous expensive words, point being, the exhuast manifold looks ok, dont hear any leaks when idling, cant hear any leaks but cant tell over the whine of the car, it has always made a high pitched leak sound but it comes out of the right end of the exhuast, probably due to my small 2.5" exhaust, my stock dump is bigger.

Link to comment
https://www.sau.com.au/forums/topic/125978-hesitation-over-45k-loss-of-power/
Share on other sites

Sounds like its mis-firing?

Do a search for missing or mis-firing or sparks or coils or coilpacks. Should come out with some answers?

Id say check sparks and coils for hairline fractures. or just check sparks and buy new splitfires :yucky: mmmm yummy. :laugh:

Also check AFM is working properly.

cleaned recently with electrical parts cleaner stuff, spray on shite you buy

It doesnt really miss fire, was fine had been driving for a while then booting it comeing onto the freeway to get up to speed and hesitation and i stopped excellerating, its fine below 4k rpm but soon as you hit the second stage boost it goes nowhere

also has 2 other issues worth noting, has unknown size deep purple injectors and has always run rich while i've owned it, also has had a swap to platinum plugs 2-3 months ago

Edited by gts-4 dreamer

I should have specified a bit more, aparently STOCK AS A ROCK power wise STOCK BOOST !, unless you count a muffler change, which is all, + the adjustable shocks and quick shifter she's completely stock, had no idea the injectors on s2's were deep purple, every one I have seen have been black or white and when i asked onthe forum specifically about htem was not answered, aparently too silly a question eh?

anyways

the problem has all but disapeared, it only seems to happen once the car is warm and when i mean warm HOT, aparently the misses must have used the loud pedal a fair bit on the way to pick me up cuase I had to take it to a track to heat it up enough to get it to start doing it which is did after about 20 minutes of hard running.

still sound like cracked plugs or coils ?

WIERD !!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Input shaft bearing. They all do it. There is always rollover noise in Nissan boxes - particularly the big box. Don't worry about it unless it gets really growly.
    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
×
×
  • Create New...