Jump to content
SAU Community

Ohlins Coilovers, Too Low For Me!

glaze
 Share

Recommended Posts

glaze Mentor

glaze

Posted
Posted (edited)

Hey guys, Just picked up my GTR and it has Ohlins Coilovers in i that are too low for this creaky old body, was wondering if anyone wanted to swap theirs for mine. Want height adjust if I can so the car is slightly lower than standard and a little softer for my back. Let me know if anyone is interested. Thanks guys.

Oh and my exhaust is bloody big and loud, would like to trade for something a little quiter, will try and give specs tomoz but I think it is a mandrel bent 4.5 inch,it is big. Let me know. Pics of how car sit and size of Exhaust.

post-8487-1153031228.jpg

post-8487-1153031362.jpg

Edited by glaze
Link to comment
https://www.sau.com.au/forums/topic/126220-ohlins-coilovers-too-low-for-me/
Share on other sites
Sydneykid Grand Master

Sydneykid

Posted
Posted (edited)
Hey guys, Just picked up my GTR and it has Ohlins Coilovers in i that are too low for this creaky old body, was wondering if anyone wanted to swap theirs for mine. Want height adjust if I can so the car is slightly lower than standard and a little softer for my back. Let me know if anyone is interested. Thanks guys.

Oh and my exhaust is bloody big and loud, would like to trade for something a little quiter, will try and give specs tomoz but I think it is a mandrel bent 4.5 inch,it is big. Let me know

Japanese Ohlins are OK shocks, they are usually height adjustable either via circlips grooves or screw thread lower sprng seats. What height is it, all 4 corners, centre of wheels to guards? Once I know that I can make some suggestions. I have worked on several GTR's equiped with Ohlins, usually a quick height increase and/or a spring srate change makes them a pretty good set up. Don't thow out the baby with the bathwater.

;) cheers :D

Edited by Sydneykid

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...