Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...
  • 5 months later...

Hey

I ended up getting the castrol vmx80 for my gearbox but i never bought any diff oil, i'm about to get some of that redline 75W90 for the diff, the only thing i'm not sure about is do i go for the synthetic oil or the shockproof oil? on there site the 75w90 is listed under synthetic only, not shockproof.

If i do go for shockproof, should i get the superlight - lightweight or Heavy.

thanks

Edited by Hulk1010
Link to comment
https://www.sau.com.au/forums/topic/126666-diff-oil/#findComment-2806116
Share on other sites

Redline 75W90 Gear Oil is supposedly good.

I use it in my diff it is very very good , always had problems around roundabouts and tight corners with the inner wheel locking up tried a few oils none were any good , redline fixed my problem

I thought shockproof isn`t an LSD oil only for the gearbox, i use the Blue shockproof in my gearbox its mad too

Link to comment
https://www.sau.com.au/forums/topic/126666-diff-oil/#findComment-2806488
Share on other sites

LightWeight ShockProof™

A unique gear oil designed to lubricate racing transmissions and transaxles which see serious loads (not recommended for most syncro-type transmissions). It has excellent low-temperature flow which allows easier shifting when cold. May be used to obtain maximum power transfer in racing differentials which do not see high temperatures. Similar to a 75W140 gear oil, but with the lower internal friction of an SAE 30 motor oil.

Used in two-stroke and four-stroke motocross transmissions (often mixed in equal parts with SuperLight ShockProof™ Gear Oil).

Used in most road-racing differentials with moderate power and dogring racing transaxles.

Taken off the redline website , funny it not recommended for most synro gearboxes works mad in mine

Link to comment
https://www.sau.com.au/forums/topic/126666-diff-oil/#findComment-2807902
Share on other sites

Yeah I'd make sure its suited to LSD diff's though..

You don't need "LSD" oil for a standard viscous diff. the viscous LSD unit is sealed from the rest of the diff enclosure and has its own fluid.

If you have a clutch type LSD (ie, you have a GTR, or your diff centre is aftermarket, or you have a skyline with A-LSD) then you need an "LSD" oil with friction modifiers in order for the clutch plates to work properly.

Link to comment
https://www.sau.com.au/forums/topic/126666-diff-oil/#findComment-2808155
Share on other sites

I went to repco, autobahn and super cheat auto today and none of them had any redline products that i could see, where can i buy this stuff besides online?

--Nevermind just found some contact locations on there site--

Edited by Hulk1010
Link to comment
https://www.sau.com.au/forums/topic/126666-diff-oil/#findComment-2820264
Share on other sites

instead of wasting your money on expensive redline which wont' do anything, because your diff is viscious (separate fluid for the viscous), I would honestly, use a castrol fluid.

Castrol lsx90. Cost ya about $30 for a 4L big bottle. You'll need 1.8L.

Castrol oils are a fairly good place to start from. At least it'll be correct.

Then, see how it feels, if it's good, then fine, it's good. From there, if you have a problem, then go mucking around with different fluids.

I have a mech diff, so I'm using motul oil, just so it changes the properties (won't do much to a viscous).

Link to comment
https://www.sau.com.au/forums/topic/126666-diff-oil/#findComment-2820448
Share on other sites

You don't need "LSD" oil for a standard viscous diff. the viscous LSD unit is sealed from the rest of the diff enclosure and has its own fluid.

If you have a clutch type LSD (ie, you have a GTR, or your diff centre is aftermarket, or you have a skyline with A-LSD) then you need an "LSD" oil with friction modifiers in order for the clutch plates to work properly.

So you only need LSD oil for a mechanical LSD? And viscous LSD has a sealed in amount of its own special fluid you dont ever need to change??

Link to comment
https://www.sau.com.au/forums/topic/126666-diff-oil/#findComment-2821002
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...