Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...
  • 5 months later...

Hey

I ended up getting the castrol vmx80 for my gearbox but i never bought any diff oil, i'm about to get some of that redline 75W90 for the diff, the only thing i'm not sure about is do i go for the synthetic oil or the shockproof oil? on there site the 75w90 is listed under synthetic only, not shockproof.

If i do go for shockproof, should i get the superlight - lightweight or Heavy.

thanks

Edited by Hulk1010
Link to comment
https://www.sau.com.au/forums/topic/126666-diff-oil/#findComment-2806116
Share on other sites

Redline 75W90 Gear Oil is supposedly good.

I use it in my diff it is very very good , always had problems around roundabouts and tight corners with the inner wheel locking up tried a few oils none were any good , redline fixed my problem

I thought shockproof isn`t an LSD oil only for the gearbox, i use the Blue shockproof in my gearbox its mad too

Link to comment
https://www.sau.com.au/forums/topic/126666-diff-oil/#findComment-2806488
Share on other sites

LightWeight ShockProof™

A unique gear oil designed to lubricate racing transmissions and transaxles which see serious loads (not recommended for most syncro-type transmissions). It has excellent low-temperature flow which allows easier shifting when cold. May be used to obtain maximum power transfer in racing differentials which do not see high temperatures. Similar to a 75W140 gear oil, but with the lower internal friction of an SAE 30 motor oil.

Used in two-stroke and four-stroke motocross transmissions (often mixed in equal parts with SuperLight ShockProof™ Gear Oil).

Used in most road-racing differentials with moderate power and dogring racing transaxles.

Taken off the redline website , funny it not recommended for most synro gearboxes works mad in mine

Link to comment
https://www.sau.com.au/forums/topic/126666-diff-oil/#findComment-2807902
Share on other sites

Yeah I'd make sure its suited to LSD diff's though..

You don't need "LSD" oil for a standard viscous diff. the viscous LSD unit is sealed from the rest of the diff enclosure and has its own fluid.

If you have a clutch type LSD (ie, you have a GTR, or your diff centre is aftermarket, or you have a skyline with A-LSD) then you need an "LSD" oil with friction modifiers in order for the clutch plates to work properly.

Link to comment
https://www.sau.com.au/forums/topic/126666-diff-oil/#findComment-2808155
Share on other sites

I went to repco, autobahn and super cheat auto today and none of them had any redline products that i could see, where can i buy this stuff besides online?

--Nevermind just found some contact locations on there site--

Edited by Hulk1010
Link to comment
https://www.sau.com.au/forums/topic/126666-diff-oil/#findComment-2820264
Share on other sites

instead of wasting your money on expensive redline which wont' do anything, because your diff is viscious (separate fluid for the viscous), I would honestly, use a castrol fluid.

Castrol lsx90. Cost ya about $30 for a 4L big bottle. You'll need 1.8L.

Castrol oils are a fairly good place to start from. At least it'll be correct.

Then, see how it feels, if it's good, then fine, it's good. From there, if you have a problem, then go mucking around with different fluids.

I have a mech diff, so I'm using motul oil, just so it changes the properties (won't do much to a viscous).

Link to comment
https://www.sau.com.au/forums/topic/126666-diff-oil/#findComment-2820448
Share on other sites

You don't need "LSD" oil for a standard viscous diff. the viscous LSD unit is sealed from the rest of the diff enclosure and has its own fluid.

If you have a clutch type LSD (ie, you have a GTR, or your diff centre is aftermarket, or you have a skyline with A-LSD) then you need an "LSD" oil with friction modifiers in order for the clutch plates to work properly.

So you only need LSD oil for a mechanical LSD? And viscous LSD has a sealed in amount of its own special fluid you dont ever need to change??

Link to comment
https://www.sau.com.au/forums/topic/126666-diff-oil/#findComment-2821002
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I think the concept is highlighting the various scenarios where thicker oil helps, and thicker oil potentially doesn't help and only generates heat and costs power, in turn for safety which isn't actually any safer (unless you're going real hot). If anything this does highlight why throwing Castrol 10w-60 for your track days is always a solid, safe bet. 
    • Jason should have shown a real viscosity vs temp chart. All the grades have very little viscosity difference at full operating temperature.
    • Oops... I meant to include the connector  view... BR/W - power from fuse L/W - motor negative to fan control amp (and off to HVAC pin19) OR/B - PWM signal (from HVAC pin20) B --  ground  
    • Yep, if you are applying filler it sounds like there is something wrong with the body lol. Safe to assume there is going to be a lot of sanding going on if your still applying fillers.  Picture a perfect bare metal panel, smooth as glass. You lay down your primer, it's perfect. (why are you going to sand it?) You lay down the colour and clear, it's perfect. No sanding at all took place and you've got a perfectly finished panel.  You won't be chasing your tail, sounds like you were prepping to start laying filler. If your happy with the body after the sanding, there is some bare metal exposed and some areas with primer, no issues at all, start laying the filler. You are safe to lay filler on bare metal or primer (of course check your technical data sheet as usual for what your filler is happy to adhere to).  This isn't a 100% correct statement. There is primer that is happy to adhere to smooth bare metal. There are fillers that are happy to adhere to smooth bare metal. Just make sure you're using the right materials for the job.  Typically if you are using filler, you would go primer, colour and clear. I've never seen any instances before where someone has laid colour over body filler (maybe this happens, but I haven't seen it before). So your plan sounds pretty normal to me. 
    • I don't think there's any way someone is push starting this car.. I honestly can barely move it, and moving it and steering it is just flat out not possible. I'm sure it is, but needs a bigger man than me. I have a refurbished starter now. The starter man was quite clear and consise showing me how nothing inside a starter really should contribute to slow cranking, and turned out that for the most part... my starter was entirely fine. Still, some of the wear items were replaced and luckily it didn't show any signs of getting too hot, being unfit for use, etc. Which is 'good'. I also noticed the starter definitely sounded different, which is a bit odd considering nothing should have really changed there.... Removed and refit, and we'll pretend one of the manifold bolts didn't fully tighten up and is only "pretty" tight. GM only wants 18ft/lb anyway. I also found a way to properly get my analog wideband reading very slightly leaner than the serial wideband. There's Greg related reasons for this. The serial output is the absolute source of truth, but it is a total asshole to actually stay connected and needs a laptop. The analog input does not, and works with standalone datalogging. Previously the analog input read slightly richer, but if I am aiming at 12.7 I do not want one of the widebands to be saying 12.7 when the source of truth is 13.0. Now the source of truth will be 12.65 and the Analog Wideband will read 12.7. So when I tune to 12.7 it'll be ever so slightly safer. While messing with all of this and idling extensively I can confirm my car seems to restart better while hot now. I did add an old Skyline battery cable between the head and the body though, though now I really realise I should have chosen the frame. Maybe that's a future job. The internet would have you believe that this is caused by bad grounds. In finding out where my grounds actually were I found out the engine bay battery post actually goes to the engine, as well as a seperate one (from the post) to the body of the car. So now there's a third one making the Grounding Triangle which is now a thing. I also from extensive idling have this graph. Temperature (°C) Voltage (V) 85 1.59 80 1.74 75 1.94 70 2.1 65 2.33 60 2.56 55 2.78 50 2.98 45 3.23 40 3.51 35 3.75 30 4.00   Plotted it looks like this. Which is actually... pretty linear? I have not actually put the formula into HPTuners. I will have to re-engage brain and/or re-engage the people who wanted more data to magically do it for me. Tune should be good for the 30th!
×
×
  • Create New...