Jump to content
SAU Community

Recommended Posts

Quick question, how do we mix the gauges we want into the $175 bundle when ordering from the website?

The only way i can see to do it is select the items individually but that ups the price quite a bit past the $175 mark.

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

Quick question, how do we mix the gauges we want into the $175 bundle when ordering from the website?

The only way i can see to do it is select the items individually but that ups the price quite a bit past the $175 mark.

Hi mate, we have a number of preset options on the website as far as the bundle pack goes, but if you want to customize the pack, simply pm me and I will provide instructions for direct deposit payment.

Nice and simple.

Cheers,

Steve

  • 3 weeks later...
  • 2 weeks later...

Hey Mate,

Would you do a special price if i buy the lot (5x)? thats boost, oil press, oil temp, water temp & air fuel ratio plus gauge holder delivered?

Cheers.

  • 3 weeks later...

Pm's replied, thanks all.

We have hundreds of gauges in stock ready to go.

Questions? Please dont hesitate to ask.

Cheers,

Steve

i'll ask him but it fits and it fits nice. wish my r33 has factory centre consoles like that. perfect fitment and looks the goods at night.

Hi, I'd also really like to see them if it's not too much trouble.

I'm planning on installing the 3 guage pack in my factory guage cluster.

Did he mount them behind the clear plastic covers, or were they removed?

hey, im thinking of getting a 3 Gauge Din Holder from your site.. i just want to make sure that they fit the 60mm apexi l2 series gauges?. they fit ok?. thinking they should :) ?

2in is 50.8mm so will not fit.

really damn.. thanx for that.. lucky i didnt buy one :santa:

any one seen and 60mm versions of the 3 gauge holder

i just bough two of these style gauges with a greddy r33 2 pod a-pillar mount. all in all a top setup. my 2 mates bought the $175 deals and we will install them tomorrow...

Edited by frozenwaffles
i just bough two of these style gauges with a greddy r33 2 pod a-pillar mount. all in all a top setup. my 2 mates bought the $175 deals and we will install them tomorrow...

Thanks for your order :) If there is anything else you need please dont hesitate to ask!

We would love to see some pics of your dual gauge setup, so dont be shy to post them up :)

Cheers, and happy new year.

Steve

how much for the single din 3 gauge installed?

Hi Dan, unfortunately we dont offer an installation service on gauges im afraid.

Steve




  • Latest Posts

    • all brand new unit from Tomei, fluid, bearings, etc. Tomei said they call it a 1.5 lsd because its 100 percent lock up under acceleration and 50 percent under deacceleration.  as I mentioned I used their fluid, install and their break-in procedure, (alot of figure 8's) but even when driving straight, or even slowly backing out of garage for first time, (at 2 mph) then driving to and from figure 8 parking lot, each tire in the rear would sporadically grab, skip, bounce, shutter and skip, shutter back a force I could feel causing clutch to slip then grab, at any speed. shaking entire car. I removed unit, since I put stock back in and all is fine, via process of elimination, its something with the lsd unit itself. I wasn't going to beat up the entire car more or change anything else for no reason as I had a feeling something in the lsd itself was wrong as everything was fine before this alone was installed and I rechecked over everything else after first time backing out I suspected an issue. I'll probably sadly already need new tires now just from trying to drive it 5 miles and performing the figure 8 break in. but if someone has any ideas I'm all ears 
    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
×
×
  • Create New...