Jump to content
SAU Community

Rb20det Loom Help...

Simon-S14

By Simon-S14,
in Engines & Forced Induction

 Share

Recommended Posts

Simon-S14 Grand Master

Simon-S14

Posted
Posted

Have had huge issues with my RB20det lately, probs are, ignition cutting out at various points in the rev range (not a miss fire like a plug or coilpack would do, but rather a total ignition cut of all 6 cylns) Some times the problem is only while drifting through corners and not in a straight line.. but a couple of times it has happened while on fullboost in 3-4th gear in a straight line and the ignition will cut out, come back, cut out quite repetively.

Now while this is happening, the Tacho also dies... so to me it indicates a loose wire, or a problem somewhere in the wiring of the ignition system. This resulted in me pulling my loom out.. have a look at it and tell me if all the electrical taping in black is factory or not? I know the red tape looks to be non factory...

1003708vs2.jpg

1003708hk0.jpg

Link to comment
https://www.sau.com.au/forums/topic/127226-rb20det-loom-help/
Share on other sites
predator Grand Master

predator

Posted
Posted

Nissan does some funny stuff with its wiring, and I believe it is hand wrapped. Some of the black tape looks like a home job, but it's actually factory. Mine was the same. Red is probably extras somebody else has added on.

It could be a CAS problem? A few have had that problem on rb20det's. I think the ECU determines the RPM / Tacho signal from the CAS as well.

darkl0n Contributor

darkl0n

Posted
Posted

i had a issue like this, it would drive fine, then it would start cutting out. it did not matter if you were in a high or low gear, some times i could rev it to 7k and it would be fine, then other times it would just cust out.

i replaced the o2 sensor and it has been fine ever since.

predator Grand Master

predator

Posted
Posted

To test if its the o2 sensor.. remove the o2 sensor plug. Car will work fine without it. Just won't run in closed loop mode, and you'll use more petrol.

Its something like the o2 sensor immitantly sends faulty signals the ecu has problems. But if you remove it totally you can isolate the problem a bit more closely.

I'm not sure how you test the CAS, you'd need to monitor the voltage signals, or use the consult connector to see what's going on.

Also when it does fail, stop the car, and put the ecu in fault mode, and it should flash the sequence for the last thing that failed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Jarsky
      After market rear camber arm adjustment

      By Jarsky · Posted

      This. A 3d wheel alignment is like $120...just take it to the shop. Since theres probably multiple adjustments that need to be made after changing something. Mine has front/rear lower arms, traction rods, tension rods, camber arms, toe arms, front upper arms, hicas kit, sway bars and coilovers. I measure from the edge of the bolt holes on the originals and set the same length on all the adjustable stuff to dial it as close as I could to OEM. Took it straight for alignment; it didnt feel right at all...after alignment, it feels perfect. Similarly i've just changed the springs on another car; and I still needed multiple adjustments to bring it back in spec.
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      A full Veilside kitted JZA80 Supra in Meriken park in Kobe city a few weeks back
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Its a well known brand in New Zealand; its a rebrand of the Rhino RAV3.  I don't know what the wiring difference *is* between the rev.1 (installed about 15 years ago) and rev.2; but as you say I would think its reasonable that it uses the same immobiliser relay circuits. I had a look but couldnt see a similar harness; but didnt move things around since I didnt want to mess with it   It was one of AVS well known Authorised Installers; I spoke to AVS themselves about it but theyre unsure hence seeking advice more so from the skyline community who are more familiar with the actual car and its wiring. Im in Auckland; but the installer is on the other side of the city so hes very reluctant to come back to even look at it to confirm something isnt connected into the wrong wire.  I dont want to drop the name since they *did* do a really good job for the most part. Everything is very tidy and he fully replaced all the alarm wiring, all the sensors, the wiring to the door motors, installed a switch which was never installed in the first place...really happy with the alarm install itself..just not this one issue. We all make mistakes, if it is the alarm, I just want my fuel pump getting proper switched, fused, power as it was; without having to shell out for an auto electrician to switch a wire and tell me it was the alarm. 
    • pacman_1219
      Blue/grey smoke after idle

      By pacman_1219 · Posted

      Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
×
×
  • Create New...