Jump to content
SAU Community

Help Needed Epa Test Troubles

NVMYTG

By NVMYTG,
in General Maintenance

 Share

Recommended Posts

NVMYTG Contributor

NVMYTG

Posted
Posted (edited)

my r33 gtst needs to pass an EPA test and to do so i need to have standard boost control parts running. at the moment i have a duel stage boost controller and it runs fine with the duel stage. when i put the vac lines to the standard controller it overboosts. can someone tell me what vac lines need to go where? also i have made sure the plug that comes from the standard controller is plugged in and i have even tried another one from a mates car. could the wiring for the standard controller be used for the aftermarket unit? if so what should i be testing for with the multi meter? the after market controller has an earth wire and a wire running through the firewall and i cant see if the wire from the standard plug has been cut as it dissapears into a loom. any help would be much appreciated. thanks, brad (also my car has a standard turbo,FMIC and at the moment the airbox is fitted and i have checked for vaccum leaks)

Edited by NVMYTG
Link to comment
https://www.sau.com.au/forums/topic/127617-help-needed-epa-test-troubles/
Share on other sites
RANDY Veteran

RANDY

Posted
Posted

You won't need a multimeter... the standard solanoid should give 5psi if it's not working properly, and 7psi if it is.

I suggest that your plumbing is not quite right... from the intake pipe down the bottom, the pipe should come into the bottom of the solanoid (I think.. if not, switch them around), and then the top one goes to your wastegate actuator.

NVMYTG Contributor

NVMYTG

Posted
  • Author
Posted

i treid the lines both ways but i was a little worried id do some damage can anybody confirm which way they are supposed to go? also id like to know what im looking for with a multimeter with the wires coming from the solinoid as i said before i tried the vac lines both ways and i even tried another solinoid from my mates car which i know works.

Mick Mentor

Mick

Posted
Posted

from memory one of the lines was running to a T peice, also one line had a little restrictor in it, if thats not in the right place that may cause your problem.

Let me work out what needs to go where cos im in the exact same boat as you, i have a dual stage boost controller installed and i need to put the standard one back on so i can get it trough RoadWorthy.

Mick Mentor

Mick

Posted
Posted

Ok here is what i worked out on how to properly install the stock boost controller.

First off there is a hose from the actuator goin to a T peice, its only short and it has a yellow band on it because it has a brass restrictor in it.

From the T peice it goes to the BOV retuirn pipe.

Then from the T peice it goes to the bottom of the boost controller.

The last is a straight hose goin from the intercoller pipe to the top of the boost controller.

Can someone please confirm this for me, i just want to be %100 sure.

I mainly want to know if the restrictor is in the short hose coming off the actuator and goin to the T peice.

I hjope this helps, im %99 sure this is right which i would love someone to confirm this all for me ..

mad082 Grand Master

mad082

Posted
Posted (edited)

no thats wrong.

(if you have a front mount there will be a hose from the bov pressure line (the vacuum hose that opens the bov) instead of the intercooler pipe)

there should be hose hose from an intercooler pipe. this goes to a T piece. from the T piece there should be 1 hose going to the wastegate, and 1 to the lower hose of the factory solenoid. the top hose of the solenoid should go back to the intake (bov plumback pipe).

Edited by mad082
Mick Mentor

Mick

Posted
Posted

Ok this is straight from the Nissan Fast program, so thjere is no disputing it.

Top of the boost controller goes straight to the wastegate.

The bottom goes to the T peice.

One side of the T peice goes straight to the intercooler pipe.

The other side of the T peice goes straight to the BOV return plumbing.

Thats it, 100%..

Mick Mentor

Mick

Posted
Posted (edited)

I also found a picture in another thread showing the stock setup i described.

The restrictor is in the short hose goin from the intercooler pipe to the T peice, make sure you have the restrictor in place.

http://www.skylinesaustralia.com/forums/in...st&id=45802

Edited by Mick

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...