Jump to content
SAU Community

Recommended Posts

Hi guys, I drive a 1990 R32 GTR. Unfortunately, there's coolant draining out when the car is running, not from the heater hoses or rad hoses, but rather somewhere underneath the intake manifold near the 4th/5th/6th cylinders. There's also oil down the side of the block. Any ideas what's wrong?

Link to comment
https://www.sau.com.au/forums/topic/128042-leaking-coolantoil-badly/
Share on other sites

Most probably a welsh plug has rusted through although that would be water only, maybe 2 have gone and thats why theres oil as well. In that position, your up for alot of work just to get to them or whatever the problem is, as the intake manifold would have to come off completely, the welsh plugs are quite easy to replace though :D

yeah could be head gasket too, or even a cracked block if you are really unlucky. But start with the welshplug theory, get it up on a hoist and check them all out.

Is the oil a seperate leak? coming from the cam cover gasket maybe?

sounds to me like the same problem that I had with my car - the welsh plug was rusted like a mofo, and it leaked through there. Im not sure about the gasket, but take it to a reputable mechanic to get it checked out. If its not under warranty, be prepare to pay a fair bit. Good luck bud.

we removed the head and wow is that ever a pain in the ass job to do.

the intake is such a pita and the coolant lines over on the turbo side are disgusting.

Turns out the coolant was coming from a hose underneith the intake manifold. The oil has made all my coolant lines soft and one finaly burst with the pressure.

So now that just leaves the coolant in the oil.

We are replacing the head gasket and bolts and hoping that clears the problem up.

The oil down the side of the block was just the valve cover:P

At least this has allowed me to find my vaccumm leak:)

just going to change all the vaccumm lines while the manifold is off.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...