Jump to content
SAU Community

Recommended Posts

Thanks, could someone please tell me whether this vehicle I am interested in buying is a v-spec or not as it was advertised as one and has brembos etc but im not sure it is, would it say V-spec instead of GT-R in the FAST results? Thanks very much in advance :(

the vin check tells you the car is christal white (326) with grey interior (G), runs an RB26DETT GTR, 4WD & was built in March 93', if all of this adds up plus it has Brembo Brakes, Retuned ATTESA E-TS system & had 17" BBS wheels with 225/45/17 tyres at some point then you should be pretty right, im not actually sure if the R32's come up as GTR/V on the VIN FAST instead of GT-R or thats just the R34's? can anyone else confirm this?

Edited by azzafreddy
the vin check tells you the car is christal white (326) with grey interior (G), runs an RB26DETT GTR, 4WD & was built in March 93', if all of this adds up plus it has Brembo Brakes, Retuned ATTESA E-TS system & had 17" BBS wheels with 225/45/17 tyres at some point then you should be pretty right, im not actually sure if the R32's come up as GTR/V on the VIN FAST instead of GT-R or thats just the R34's? can anyone else confirm this?

yea 33/34 show V Spec, 32z only show GT-R or GT-R.17

2 check models in FAST type 'r32' in "Model series", click OK,

then the top right button out of the 8 Jap buttons (DU-AD)

cheerz

Can anyone provide either: a page that details which codes relate to which options, or in particular ABS on BNR32, or A VIN of a GT-R which came with ABS from factory using the 1inch brake master (not brembos).

Thanks guys.

Also could someone fast HNR32001765 for me :banana:.

Thanks again.

::Z54

definatly not, I'm not sure what the .17 indicates(I assume it'ssomething to do with 17"Rims), but they are the only 2 posibilities FAST can give

Can anyone provide either: a page that details which codes relate to which options, or in particular ABS on BNR32, or A VIN of a GT-R which came with ABS from factory using the 1inch brake master (not brembos).

Thanks guys.

your best bet is :- Decode Model Numbers Scroll down a bit

Also could someone fast HNR32001765 for me :thumbsup:.

post-68505-1269592945_thumb.jpg

Thanks again.

Cheers Bundy

Cheers bundy there is no mention of ABS on R32 GT-R model codes and on 33's it appears to be in the same position and the same letter as the 32s steering wheel designation *puzzled*

Similar information is here: http://www.skylinesaustralia.com/forums/Vi...amp;hl=decoding with reference to the original thread which has a dead URL.

It suddenly strikes me.. do all 32 GT-Rs except N1s have ABS?

Cheers bundy there is no mention of ABS on R32 GT-R model codes and on 33's it appears to be in the same position and the same letter as the 32s steering wheel designation *puzzled*

yea different models are decoded different. pita

Similar information is here: http://www.skylinesaustralia.com/forums/Vi...amp;hl=decoding with reference to the original thread which has a dead URL.

It suddenly strikes me.. do all 32 GT-Rs except N1s have ABS?

I think your on to sometheing there, had a look at Motor Traders (known verified info), looks like all 32 GT-R and GT-R Vspec (including V spec II) have ABS as standard, main options are fog lamps,drivers airbag and rear wiper in later models

cheers

Edited by BundyBear

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You don’t need to use full throttle all the time to break these blocks, 500kw at the wheels in more then enough to break them even with an occasional squirt. Hell I’ve seen them break under 400kw
    • A work around is to install the R35 card style AFM/MAF on the cold side of the intercooler piping and the BOV on the hot side piping. Works well, also you can combat the revs dropping by adding a bit more ignition timing on the idle ignition timing table to slow the rate of RPM drop.
    • Understood. If you dont have a ridiculous limit,  Tune, T's and P's are in check, and arent bashing it all the time and doing the due deligence for maintenance(inc oil analysis) then its pretty safe. 100% agree, let your right food control it to some extent.
    • So these external kits with the machined block for remote solenoid mount will only work on a NEO head and RB30 or RB26 bottom end   For an R33 head on a 26 bottom end the remote vct kit is to resolve RB26 manifold adaptor plates etc  IF you try to use the remote VCT on an RB30 or RB26 bottom end with an R33 head then  you can starve the cam journal??? I have one of these kits from bits I had years ago before plans changed  I don't understand how that tracks with this video   https://youtu.be/RuPiI22Mplk?feature=shared   This looks like I can run the v termite vct kit to feed the VCT on an R33 head on an RB26 bottom end?!?!?   Lol.... don't v have these problems on RB20s
    • Yeah i know that MAF is no no for this type of BoV. The engine has no BoV and "hose/pipes" ..it was all deleted (or probably it was not even on the engine when it was bought  ) It does that "sutututu" noise which i kinda do not want(atmospheric is better IMO...but standalone ECU)  What are the cons of running without blow off on stock RB25DET NEO. It running 5-7 PSI max (it has boost controller)   EDIT: and can Nistune be "tuned" to know there is no BoV to i dont know "know" and be better for a car? I read so many info about no BoV. One guy saying it is bad and hurting the turbo/engine/car and other that it does not...  
×
×
  • Create New...