Jump to content
SAU Community

Recommended Posts

In that case, you may well still have the auto diff which means lower top speed but quicker acceleration. (like mine) :woot:

Need to try find a couple of R33 brochures I have and put on my magical japanese head for translating some of these questions. :/

Miguelone may be onto something...

Can anyone else break the code???

Edited by Not a Pulsar

can someone do BNR34006208 + show optional extras

and can anyone tell me what the little x's mean in the model code GGJPRWY34Zxxxxx-x

The first x after the Z is not a D, which i haven't seen before on a r34 model code.

Thanks in advance

can someone do BNR34006208 + show optional extras

and can anyone tell me what the little x's mean in the model code GGJPRWY34Zxxxxx-x

The first x after the Z is not a D, which i haven't seen before on a r34 model code.

Thanks in advance

vwxwys.png

Can't help with decoding R34 model codes :/, had a quick look on the net and couldn't find any info unlike with 32's & 33's.

Edit: found something

15yr0m.png

The character after the Z is the destination, As far as I know the only place outside of Japan 34GTR's were sold was the UK and not very many. Could your R have come from the UK?

thanks mate.

I was looking through the workshop manual (thats where that model variation image is from) when i decided to check my model code and that extra Z caught my eye.

It could have come from the UK - anythings possible - i also think a few got sold in NZ too

i'll check out the uk site and see what i can come up with.

mmm could be that. i know the r33 had a cold district specification, so it makes sense that the r34 had one. I don't think i have heated mirrors though

Regardless, the car's in pretty good condition if it came from a snow region.

post-78856-0-17899800-1348211497_thumb.jpg

Thx mate not sure about the model code and what it means RNR32GASLMDB but it says engine RB20DT but it is a DET does that mean orig it wasn't tubo and was fitted later?

What does 4K and the HI . 4WD mean? Prod M/Y 9007 does that mean build date July 1990?

I really do appreciate you taking the time to look it up for me, thx heaps.

fastformyskyline.jpg

Edited by Aljo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...