Jump to content
SAU Community

Recommended Posts

Thats good news, thought we might get squeezed out.

Should get there early to grab a carport.

Paul see if you can get boosted zed to come out to play. :)

i would say not much chance of a carport unfortunately. might be able to get one for the morning but in the arvo guys will be wanting to move in to their alloted bay (i know we will!).

good news paul on the session structure. should make for a fun day then :woot:

  • Replies 77
  • Created
  • Last Reply

Top Posters In This Topic

looks like my shift at work is changing and fridays are my saturdays...

SO....could be a goer for me!! :(

and now that my brother decided to have his bucks party on the fatz grip n drift day - this day looks much better for me.

many spots left?

heheheh

Paul - not sure if you eremeber mer - but few years back I dud an SAU track day in my LS1 - signed up on the skylines downunder - was over 3 years ago- so you guys have gotta be nice to me as ill be back to beginer skill !!

I think I do remember, that was a while a go. Everyone has to be a beginner at some stage, its nothing to worry about, its more important that you just get out and have some fun, and not do it on the steets.

Im in the R32 GTS-T doing some development and practice, its my first full track day in this car so I dont expect to be doing V8 times or anything like that either.

Nice one!

:)

Cheers Paul - cant wait to get back out there!

whats the expected turnout of cars? Is it similar to the motoconcept days where theres group a, b and c?

OK,

They run 3 groups. 20min of each hour

C3/4 Cars (Normal race car licence group)

Bikes (National race bikes)

L2S (Us!)

So we basically go out in 1 group, normally there will be a few super sprint guys and a few others + us. I think last time there was about 15 cars, some fast and some slow but not much to worry about.

In order of priority of what to do.

Bleed brakes with Dot 5 or 6 I use the Motul 600V, UAS have it for $50 a litre.

Check pads if they are crap pads make sure you have at least 50% wear, if you have good ones ie Frodo 2500's make sure thay are no lower then 25%. Stopping is number 1!

Tyres make sure you have about 40 PSI, you can always take air out but is a little harder to put it in, dont come out with sh!t tyres, they dont grip well and you often undone, ask yogi.

Change your oil if its older then 5000km, and get a service as well if you have not had one in a while.

If you have suspension mods 3-4 Deg of camber is a good thing on the track and caster is nice as well, so a wheel alignment is cool if you want to be hard core.

Thats about it unless its your first time your car has seen the track, and it has a few mods. It may need pay to get a retune, ie street or drag tune cars dont always last 8 x 20min at full noise.

I think thats it, see you out there.




  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...