Jump to content
SAU Community

Recommended Posts

hey guys i got a power fc on my r33. i was just wondering if my power fc reads a temp of over 90 after a while of driving should i be worried? the temperatire needle is always on half way so it seems ok there, but just wondering what should the average reading of the water temp on the power fc be.

cheers

Link to comment
https://www.sau.com.au/forums/topic/129938-rb25det-water-temp/
Share on other sites

Hmmm... How high over 90? 99 or 91?

There is a bit difference between the two. :)

If its 90/91 i wouldnt be worried, depends on other factors aswell.

Cruising 100km/h is it the same?

Is it only that temp in peak hour traffic?

Bit more info dude, but it sounds ok at this stage.

don't worry its nothing

my old man's corvette gets up to 110deg in traffic before the fan comes on

remember the water is under pressure so it boils at a much higher temperature than normal water. plus there's the anti-boil added that should assist even further..

The thermostat is 82 deg C??? On the street my handset say about 82-85. So for potting around the thermostat isnt cracking???? Or should i be checking that mine is ajmmed open. Because my temps sit so low on the street, i normally pull the pin at the track when the temp gets to around 90-95 (depends how much lomger the session is and how hot ther dy is etc if i push past 93 etc

82-85 on the street is A-OK Roy. The temp sender may not be accurate to the degree but most engine temps sit at or just above the thermostat temp. On hotter summer days it'll be 5-10C higher than the thermostat temp. Normally a thermostat will close roughly 5C lower than its set temperature.

Also I think high 90s is OK for the track. I'd probably think about pullin the plug when its more like 110C? Remember with a proper cap + coolant it wont boil until 120C.

82-85 on the street is A-OK Roy. The temp sender may not be accurate to the degree but most engine temps sit at or just above the thermostat temp. On hotter summer days it'll be 5-10C higher than the thermostat temp. Normally a thermostat will close roughly 5C lower than its set temperature.

Also I think high 90s is OK for the track. I'd probably think about pullin the plug when its more like 110C? Remember with a proper cap + coolant it wont boil until 120C.

Cool

Roy,

I think the other dude meant to say the 'R34' thermostat begins to open at 82degree's.

The R32/R33 on the other hand begins at 76degree's.

If the thermostat is genuine or not also depicts the cars operating temperature and how quickly the thermostat opens completely. The genuine opens slow and by little amounts until its nice and hot. This results in a slightly warmer running temp with less fluctuations and a considerably quicker warmup.

The aftermarkets (supercrap autostores etc) open wide and really quickly, the aftermarkets also take ages for the car to reach operating temp from a cold start. On my sisters VL it would tend to run hotter under consistent load with the aftermarket but run cooler just pottering around, in the R32 I haven't seen this problem, it simply ran cool all the time; all though I didn't get to 'really' test it out in hot weather. I dropped the genuine thermostat in the VL as it ran much better and wouldn't over heat when giving it a boot full up willunga hill.

Both genuine and aftermarkets are rated to 76.5degree's.

(I sound like a record) I recently said the same in another thread. :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
×
×
  • Create New...