Jump to content
SAU Community

Recommended Posts

Is this AFM somethin that I can change myself or do I have 2 go 2 a professionsal?????

I'm in VIC where should I go?????

Have a look here mate.

http://www.skylinesaustralia.com/forums/in...c=13305&hl=

  • Replies 91
  • Created
  • Last Reply

Top Posters In This Topic

Is this AFM somethin that I can change myself or do I have 2 go 2 a professionsal?????

I'm in VIC where should I go?????

The pin configuration is different but as long as you are handy with a soldering iron, you should be able to work it out yourself

P.S. It won't work on the stock ECU, only aftermarket.

well, off the top of my head i cannot list one honda vtec car that actually runs boost. running a map sensor from my understanding in an n/a car is no problem, but because a turbo car will reach maximum boost, usually at the latest by 5000rpm, that leaves another 2000rpm in this case, in which the map sensor will be utterly useless, and thus make tuning alot more "rough" so to speak.

Just because an engine produces 369rwkw with an AFM doesnt mean the AFM isnt causing a restriction and that there is nothing wrong with the AFM as you say. Your logic is to look at the end result without a proper control (ie no AFM) which is nothing but inviable.

Honda and certain toyotas run MAP. Have you driven a vtec-powered car?

Youre always the first to say if its not needed than dont buy it. Well what about this case? The afm isnt needed and unless youre a track racer where a split second counts the AFM isnt needed at all. He can save himself money on not buying an AFM.

The pin configuration is different but as long as you are handy with a soldering iron, you should be able to work it out yourself

P.S. It won't work on the stock ECU, only aftermarket.

what kind of aftermarket ECU should I be looking at???

Totally agree with everything below though I think the wolf is about the 1100 mark (that said it doesnt compare to the pfc and i would never recommend it even though i have one).

My bad regarding cost and AFM + CPU.

My tuner has expirience with both MAF and MAP applications for the RB's.

If he tells me in his expertise that the AFM is not a restriction, then i'll believe him based on his testing and applications.

I trusted his judgement and made more power than anyone else said was possible at the time.

When a PowerFC is $900, and the AFM $250-$300 thats $1200.

Would i be right in saying a MAP based ECU is a little more expensive in most cases?

The closest that comes to mind is $1400 at the very least. I think more decent are wire-in at a $2000+ cost

So cost for cost, the AFM + PowerFC Combo will works out cheaper.

As stated he is in Vic, and *most* tuners will prefer to use a PowerFC down here as opposed to anything else.

aphid is spot on

pressure != volume

on an n/a car anything on the intake is a restriction so they need as little crap in the way as possible. on a turbocharged car this is not true as restrictions lie after the compressor outlet.

CHANGE OF SUBJECT!!!!!!!!

gonna put a new full exaust on my r33 97". What is the meximum db can it be before I cop fine from the coppers???

90 decibels in QLD, should be about the same in NSW and VIC

Hello everyone.....

I was flicking through a "high performance imports magazine" and I saw an ad for a high performance engine rebuild kit for a RB25-DET. It consists of:

  • Venolia forged pistons
  • Grant chrome rings
  • R.E.V. I-Beam forged conrods
  • Tomei metal head gasket
  • Genuine Nissan full engine gasket kit

All of this is for $3999

Is all of this stuff at a good price or not???????

cheers :P

Edited by rob123456
So what are the new goals then?

New budget?

This time I now want 2 achieve around 250rwkw - 300rwkw. Money isn't a really big issue but I would like 2 know the most cost efficient way?????

Question:

Will I have 2 change my standard turbo in order 2 do this??? If so then what would you recomend?????

I was thinking of buying a HKS GT2530 what do you think????

Cheers :)

Edited by rob123456
im merging the threads, they are still the same then

i'm sorry massive type error!!!!!!!!!!!!!!!!!!!!!!!!!!

before I wanted 2 acheieve around 200rwkw now i would like to achieve 250 - 300rwkw

sozzzzz

Edited by rob123456

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
×
×
  • Create New...