Jump to content
SAU Community

Recommended Posts

You know, I was waiting for you to kick in with your thoughts, LOL! A voice of experience when it comes to turbos, yes?!?

Yeah, well I have popped a couple of turbos in my time...

Had to do a lot of research into which turbo I should get next (so that I dont pop another one) :P

  • Replies 668
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Yeah, well I have popped a couple of turbos in my time...

Had to do a lot of research into which turbo I should get next (so that I dont pop another one) :P

Ooh, ooh: go HKS, GO HKS!!

So when do we get to see the white pearl beast again??

I'm off to check the Lotto ticket again today, LOL!

There will be very gradual forward progress over the next 6 months, then hopefully a flurry of activity that might, MIGHT see her surface somewhere at the end of '09. Unless the ticket comes in, in which case it'll be six weeks!! Believe me, and I know you're feelin' my pain, when I say it breaks my heart to see her sitting still. I keep telling myself "It WILL be worth the wait, it WILL be worth the wait, it WILL be worth the wait..."

i have a white pearl car.. are you refering to me?

if so i dont know when it will be on the road

Jeez, I hope you're not in the predicament I'm in with my pearl white one!!

Hmmm, back on the topic of inlet pressure, wouldn't it be somewhat beneficial to have a little bit of air left behind just at the front of the throttle body so as to increase response for the next time you step on the gas?

Or does it dissipate so quickly that it's better to vent and then just get freshly compressed (and hopefully cool!) from outside again?

well i think mine is minor compared to yours, the plug leading to the ECU just needed rewiring.. then a tune etc.. should be tomorrow but there are no garantees

I'll swap you situations, LOL! Still when 'little mischief' comes back to life, it will be a happy day!!

Hmmm, back on the topic of inlet pressure, wouldn't it be somewhat beneficial to have a little bit of air left behind just at the front of the throttle body so as to increase response for the next time you step on the gas?

Or does it dissipate so quickly that it's better to vent and then just get freshly compressed (and hopefully cool!) from outside again?

Good question.

There is always a certain amount of pressure in the inlet whenever the engine is running, as the turbo never actually comes to a complete stop, BOV's have a spring (which is usually manually adjustable in aftermarket items) which will only let a certain amount of pressure out of the inlet and keep a certain amount in.

If there was 0 pressure or a vaccum in the inlet, the next time you stepped on the throttle the engine would almost always stall.

Ok back on topic, what ticks me off is F_cking kids on school holidays with nothing better to do that run around egging houses!!! :blush:

Last night I spent half an hour washing 3 eggs off the back of my house and when I went looking for the little sh_ts I managed to catch them in the act but one had his 'P's and they took off in a POS Ford Laser before I could bash their skulls in!!

I called the cops and lodged a report and all they said was "we'll keep an eye out for the car, call us back if it happens again"... I used to like living in my suburb but now its full of little 16 - 17 year old f_ckwits!! :bunny:

what ticks me off is trying to sorce parts for my skyline and no one seems to have the items i need to clear my defect not even aftermarket ones

also motor bikes who ride down the middle of trafic that is moving at pace why cant they wait like everyone else

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...