Jump to content
SAU Community

Recommended Posts

Ok, so I have most of my plumbing back together, all bar the small (8mm?) hose that connects next to the bottom radiator hose on the block. Where does this hose connect to in the system?

Also, anyone got English instructions for the D1 breather tank as I lost my instruction sheet (even if it was in japanese)

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/131935-what-is-this-hose/
Share on other sites

It's where the bottom hose fits the block on the rear side of it. I don't have a pic unfortunately. I figure that it goes in a loop to the t/body and into the runners for the plenum (ath the front end of the plenum on the top) Problem is that my new subzero plenum has the water lines blocked off. Will this cause problems if I am making sense?

the hose that is part of the throttle and bleeder system that runs off the back of the thermo housing goes up into the plenum around the injectors, then out the back of the plenum to the turbo ... you must keep this hooked up.

that's what I thought it was. Much appreciated.

I can't get a straight answer from people as to why coolant is required to go through the plenum around the injectors. But this subzero plenum has a plug on one side screwed in and some sealant blocking the back end that goes to the turbo line. So basically, it wasn't flowing coolant on it's last car and does it really need to? Cheers

I can't get a straight answer from people as to why coolant is required to go through the plenum around the injectors.
I imagine it's designed to keep the inlet runners warm, thereby improving and maintaining the vapourisation of the fuel.

I have a baby T3 that has a bigger front wheel.

The water line from that is now tee'd into my heater lines.

The small hose behind the bottom radiator hose (going into block) now connects to my breather tank.

I have been told that it's for cold start only to have the water in those runners and is better to leave dry. Should be set now.

I have been told that it's for cold start only to have the water in those runners and is better to leave dry. Should be set now.

if you could get a better explaination about this statement i would be insterested..

as for cold starts the water is cold, what would cold water do for the injectors on a cold start???

--been looking into running a bleeder tank on my car too.. good to see it works hooking it up here

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...