Jump to content
SAU Community

Recommended Posts

For camber you need the upper wishbone in adjustable form, the one pictured there i believe comes from the front-centre of the subframe and goes to the hub. You need the adjustable piece that goes from the centre-inside to the hub and around your shockabsorber up top to screw in/out rear camber.

What you need for camber adjustment.

post-12828-1156712001.jpg

Hope that makes sense :)

Edited by r33_racer

To be honest mate i have no accurate answer for that.

My guestimate would be they are some form of rear castor arms. But what they actually do or help do is beyond me. As far as i know on the rear you only have: camber, toe in/out i dont believe there is a rear castor.

Maybe its a drag racing thing or drift thing....maybe its a wank! Maybe someone with more knowledge then me may answer that one :P

R32/33/34 's have 2 upper rear control arms, both control camber.

One arm is parrallel to the drive shafts, the red R32 arm in the post above

(Note that the R33/34 arm is only one sided, not a complete loop)

The other arm is at a 45 degree angle to the drive shaft, the blue one in the post above.

To properly correct the camber you need both arms.

That's why the Whiteline rear camber kit comes with adjustable bushes for both arms.

In the following picture of R34GTR rear suspension, you can see the 2 upper arms. The inner pivots points (where the Whiteline camber bushes go) are marked with the 4 yellow dots.

R34_GT_R_Rear_Suspension.jpg

:happy: cheers :)

  • 1 month later...

Diggin up an old thread :P but why do people call this (the one on the first post) the 3rd arm, traction arm? that and quote " can be setup for drift or grip"

If you have the camber arm adjustable aftermarket, is there any need to get the other? would have them both adjustable be better?

Cheers

  • 2 weeks later...

i was visiting a a mate the other day who said i could buy the arm in the first pic realy cheap as he had brought it then decided to get the hole set with both the upper links and the forward facing traction rods.

i now see why just jap sell it all in a pack as i like many others has been miss led that you only need second one pictured.

Diggin up an old thread :( but why do people call this (the one on the first post) the 3rd arm, traction arm? that and quote " can be setup for drift or grip"

If you have the camber arm adjustable aftermarket, is there any need to get the other? would have them both adjustable be better?

Cheers

If you only use the upper control arm to adjust camber you will get severe distortion of the traction rod and lowr control arm bushes and they (all 8 of them) will wear out very fast. Plus your wheel aligner will find it very difficult to get the toe settings correct. Worst of all you will end up with bulk bump steer.

Traction rods make no difference to the rear subframe alignment which is what is required to give the adjustment of squat for traction or drift. A rear subframe alignment kit is what is required for that.

D cheers :D

Edited by Sydneykid
If you only use the upper control arm to adjust camber you will get severe distortion of the traction rod and lowr control arm bushes and they (all 8 of them) will wear out very fast. Plus your wheel aligner will find it very difficult to get the toe settings correct. Worst of all you will end up with bulk bump steer.

Traction rods make no difference to the rear subframe alignment which is what is required to give the adjustment of squat for traction or drift. A rear subframe alignment kit is what is required for that.

D cheers ;)

Ok - so what dose one use for added traction in a drag scenario?

And whilst i have your attention , who knows the best place to get some et ot Goodyear drag slicks new or used - i cant seem to find any one who has them in stock ?

corect me if im wrong but the skyline multi link rear end is clasified as a "double a arm",virtual upper a arm"

to get the right amound of angle change there pivot points are seperat.(bit hard to have one moumt where the wheel is mean to be lol. but they are one arm in motion.

so you need to do both for corect arm geometry. other wise it will be like one side of the virtually both being twisted as it goes up and down.

hope that makes some sense.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...