Jump to content
SAU Community

Recommended Posts

For camber you need the upper wishbone in adjustable form, the one pictured there i believe comes from the front-centre of the subframe and goes to the hub. You need the adjustable piece that goes from the centre-inside to the hub and around your shockabsorber up top to screw in/out rear camber.

What you need for camber adjustment.

post-12828-1156712001.jpg

Hope that makes sense :)

Edited by r33_racer

To be honest mate i have no accurate answer for that.

My guestimate would be they are some form of rear castor arms. But what they actually do or help do is beyond me. As far as i know on the rear you only have: camber, toe in/out i dont believe there is a rear castor.

Maybe its a drag racing thing or drift thing....maybe its a wank! Maybe someone with more knowledge then me may answer that one :P

R32/33/34 's have 2 upper rear control arms, both control camber.

One arm is parrallel to the drive shafts, the red R32 arm in the post above

(Note that the R33/34 arm is only one sided, not a complete loop)

The other arm is at a 45 degree angle to the drive shaft, the blue one in the post above.

To properly correct the camber you need both arms.

That's why the Whiteline rear camber kit comes with adjustable bushes for both arms.

In the following picture of R34GTR rear suspension, you can see the 2 upper arms. The inner pivots points (where the Whiteline camber bushes go) are marked with the 4 yellow dots.

R34_GT_R_Rear_Suspension.jpg

:happy: cheers :)

  • 1 month later...

Diggin up an old thread :P but why do people call this (the one on the first post) the 3rd arm, traction arm? that and quote " can be setup for drift or grip"

If you have the camber arm adjustable aftermarket, is there any need to get the other? would have them both adjustable be better?

Cheers

  • 2 weeks later...

i was visiting a a mate the other day who said i could buy the arm in the first pic realy cheap as he had brought it then decided to get the hole set with both the upper links and the forward facing traction rods.

i now see why just jap sell it all in a pack as i like many others has been miss led that you only need second one pictured.

Diggin up an old thread :( but why do people call this (the one on the first post) the 3rd arm, traction arm? that and quote " can be setup for drift or grip"

If you have the camber arm adjustable aftermarket, is there any need to get the other? would have them both adjustable be better?

Cheers

If you only use the upper control arm to adjust camber you will get severe distortion of the traction rod and lowr control arm bushes and they (all 8 of them) will wear out very fast. Plus your wheel aligner will find it very difficult to get the toe settings correct. Worst of all you will end up with bulk bump steer.

Traction rods make no difference to the rear subframe alignment which is what is required to give the adjustment of squat for traction or drift. A rear subframe alignment kit is what is required for that.

D cheers :D

Edited by Sydneykid
If you only use the upper control arm to adjust camber you will get severe distortion of the traction rod and lowr control arm bushes and they (all 8 of them) will wear out very fast. Plus your wheel aligner will find it very difficult to get the toe settings correct. Worst of all you will end up with bulk bump steer.

Traction rods make no difference to the rear subframe alignment which is what is required to give the adjustment of squat for traction or drift. A rear subframe alignment kit is what is required for that.

D cheers ;)

Ok - so what dose one use for added traction in a drag scenario?

And whilst i have your attention , who knows the best place to get some et ot Goodyear drag slicks new or used - i cant seem to find any one who has them in stock ?

corect me if im wrong but the skyline multi link rear end is clasified as a "double a arm",virtual upper a arm"

to get the right amound of angle change there pivot points are seperat.(bit hard to have one moumt where the wheel is mean to be lol. but they are one arm in motion.

so you need to do both for corect arm geometry. other wise it will be like one side of the virtually both being twisted as it goes up and down.

hope that makes some sense.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
    • Well the articals keep saying a Q50s (Skyline in Japan) with a new Manual gearbox. I like the talk about the new looks with the round tail lights. I hope they bring back the retro look like they did with the Z
    • Off the back of feedback we have decided to mix up this next Motorkhana at Avalon to have some targeted skills practice for beginners to advanced. Saturday 6th September 2025 8:30am Capped 26 entries Standard Entry Fee: $89 Members Entry Fee: $55 (SAU Victoria Only) Entries Close: Friday 5th February  Where: 55 beach road Avalon. https://maps.app.goo.gl/HNUE3EuNue3sJxh38 Entries: Limited to 26 entrants (Passengers allowed over the age of 14 with a signed disclaimer and same safety gear) Disclaimer: Download  Please electronically sign and email to [email protected] or print and hand in and Driver Sign In. To compete in this event you will require A valid  AASA General Speed licence or (Day license via the AASA Website for $50) MA Licenses are no longer accepted by AASA https://aasa.com.au/  A helmet, long sleeve clothing and a 1KG mounted fire extinguisher recommended (But not Mandatory). Further details within Supp Regs on the enty link. Entry Link > https://www.sauvic.com.au/entry/deca/20250906 You can bring and have a passenger in the car but they need to comply to the same safety and clothing as driver. Bring your car and get to battle others, win, lose or draw. I can guarantee you will have lots of fun. Any questions email [email protected] Entry List: 1.Anna S 2. Luke S 3. Jesse Givens-Lamb 4. Luca Stamatescu 5. Madeleine Stamatescu    
    • Wanna rewrite all of that in, say, 2 or 3 separate sentences, so that we can read it?
×
×
  • Create New...