Jump to content
SAU Community

Recommended Posts

post-26802-1158028554.jpgpost-26802-1158028594.jpgpost-26802-1158028639.jpgpost-26802-1158028698.jpgpost-26802-1158028722.jpg1991 model white nissan silvia sr20det

vertex rear and sides

3 inch straght throght exhust

fully stipped interior including sound deadening then sprayed in matt black

bride copy bukket seat 4 point harness and dished race steering wheel

17inch black with chrome lip wheels

custom cold air intake

custom radiator overflow tank

engine damper

front strut brace

shimmed lsd just like a locker

all aircon and heater parts removed

turbosmart type 2 bov

d2 coilovers

6mm spaced tie rod ends

comes with 8 stock wheels 4 sr type and 4 ca type plus the 17s witch are on the car

has a few minor dents nothing majour

$8000 prive very negotiable selling becouse i moved to sydney and am buying a road bike

call joe on 0415443047 any time

car is not registered but can be

comes with every stock part i have removed and some spares

Edited by sl1da

the car is in nowra so its hard for me to get pics i will try and get them up soon i have some pics on my phone if u msg me your number i can send them to you the lowest i might go would be 6500

cheers joe

Edited by sl1da

is this a standard sr20det? or has it been a transplant victim of a sr20de?

just trying to get some more information,and am i right i saying that you still have all the trim that you have taken out of the car?

one more question, how long hs it been out of rego? and can you get the blue slip done if i direct depoist into your account?

aaron

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...