Jump to content
SAU Community

Recommended Posts

Ok guys it took a straight week to tune my car but i am about confident that i have reached my goal of about 600HP. (on my gtech i push in about 520HP but correctingthis value for wind resistance and rolling resistance it will ammount to about 600 WHP) enough of that, there is a little problem i experience when the T04Z is comming on boost, according to my AEM UEGO wideband datalog my AFR is steady at 14.3 idle and the moment i hit boost the fuel curve comes down to about 12.1. but as the boost builds when im changing gears and let of the throttle i get a huge backfire about 1.4m long. i got fined for frying the lens on a policecar that was onfurtunate to drive behind. this is realy starting to irritate cuz when i pick up my GF the whole neighborhood knows im comming cuz of the huge cannon i have trailing behind me. what can there be done to resolve this problem. should i lean the tune out a bit more to about 12.5 or should this be the way things are, and is this going to hurt my turbo or the exhaust side of the head in any way? the flame does not start in the muffler it starts just after.

Link to comment
https://www.sau.com.au/forums/topic/132186-got-fined/
Share on other sites

do you have an Atmo BOV?

if so, ditch it and get a plumb-back... will solve alot of your problems... sounds like it is overfuelling on gearchange, which an Atmo BOV will cause... this is due to it 'dumping' already metered air out of the system... the computer continues to pump in enough fuel to compensate for this already-metered air (which is no longer there) hence it runs rich.

Link to comment
https://www.sau.com.au/forums/topic/132186-got-fined/#findComment-2447559
Share on other sites

i dare say that he isn't running the stock ecu, so an atmo bov shouldn't change it much.

how lean is your low load tune? that may be the problem. if your low load afr's are too rich then when you lift of it is dumping in too much fuel.

also i'd say your cat is well and truly gone.

Link to comment
https://www.sau.com.au/forums/topic/132186-got-fined/#findComment-2447732
Share on other sites

first of all i live in a country where we dont know what cats are ( at least the cops dont) hence i run a 3.5 inch full turboback exhaust (no restrictions just turbo and a pipe with a resonator in the middle and a muffler in the end). i run a PFC and after the advice of R31Nismoid i am still utilizing the stock GTR BOV's instead of going to the HKS SSQV (very pleased with my choice the dont leak shit quite surprising for a stock item) but i have vented the BOV as i dindt have time to make the piping to recirculate it. is is good if the flame is a bright blue colour?? cuz yesterday at a stopsign (around 12pm) some dude in a honda S2K tought he had a chance so the dude starts reving his engine. im at the end of my run in period (still have about 100 miles to go) so thought what the hell, revved it up to 9000 and dumped the clutch, lit up all 4 and when i changed in to second the only thing i saw in my rear view was a bright blue flame (thank god it doesnt burn the body of the car) but when i change from second to third the flame becomes a mis between yellow and blue and when hitting 4th its nearly complete yellow and 5th its yellow. so what i thing its farly lean on low load and when reaching higher load it richens up which is a good sign but the backfire bothers me

Link to comment
https://www.sau.com.au/forums/topic/132186-got-fined/#findComment-2450940
Share on other sites

ill provide the pics of the whole buil on a website i am constructing at the moment. but i am very busy at work lately and being a new dad to a set of twins its very hard to get some work done at home. the whole tuning process has video, pictures i even have a video where i run against a friend of mine with the same car he only has a HKS stroker and a T88H 34D turbo on its and makes about 800-900 HP but i did it to show him that he cant drive his car. and if i get this flamage with a cat isnt there a huge chance that i burn the internals of the cat to bits?? the next step for my car is work on the exterior and interior a bit cuz the car is fully stock on the outside. i have sent my valve & coil cover to be powdercoated and the car is going into the paint booth one of these days

Edited by Faid
Link to comment
https://www.sau.com.au/forums/topic/132186-got-fined/#findComment-2451598
Share on other sites

ill provide the pics of the whole buil on a website i am constructing at the moment. but i am very busy at work lately and being a new dad to a set of twins its very hard to get some work done at home. the whole tuning process has video, pictures i even have a video where i run against a friend of mine with the same car he only has a HKS stroker and a T88H 34D turbo on its and makes about 800-900 HP but i did it to show him that he cant drive his car. and if i get this flamage with a cat isnt there a huge chance that i burn the internals of the cat to bits?? the next step for my car is work on the exterior and interior a bit cuz the car is fully stock on the outside. i have sent my valve & coil cover to be powdercoated and the car is going into the paint booth one of these days

Vent the BOV’s back into the turbo inlet system and I bet the problem goes away. Just in case you don’t know what is happening;

1. The AFM’s measure the incoming air flow

2. The ECU squirts in the amount of fuel necessary to match that amount of air

3. The BOV’s vent the air after the AFM;s have measured it

4. So you get a whole heap of fuel with not enough air for it to be burnt in the combustion process.

5. Hence some unburnt fuel heads out of the engine into the exhaust system

6. That unburnt fuel either ignites straight away and gives a long slow reddish flame out the pipe (like a V8 Supercar on overrun)

7. Or, it sits in the exhaust until you put you foot back on the throttle and gives a nice bright ignition flash that is blue to white in colour.

Recycle the BOV’s and the problem will go away.

:) cheers :laugh:

Link to comment
https://www.sau.com.au/forums/topic/132186-got-fined/#findComment-2452497
Share on other sites

hell yeah. i know what i am doing for my next party trick he he. putting my hks ssq back on. COol oh wait i have a cat, damn it. Shame about the fine. lucky you dont live in the city. i dont know about anywhere else but in perth, something like that will grant them ability to pull your car of the road for a month.

Link to comment
https://www.sau.com.au/forums/topic/132186-got-fined/#findComment-2452919
Share on other sites

hell yeah. i know what i am doing for my next party trick he he. putting my hks ssq back on. COol oh wait i have a cat, damn it. Shame about the fine. lucky you dont live in the city. i dont know about anywhere else but in perth, something like that will grant them ability to pull your car of the road for a month.

Or you could just do a keybanger :blink:. With the mircotech i had you had to turn off the ignition to reset the

display, and kabam! Great for surrounding motorists

Link to comment
https://www.sau.com.au/forums/topic/132186-got-fined/#findComment-2452966
Share on other sites

dont live in the city, i dont even live in your country. i live far away from australia you can say on the other side of the planet. I live in the 3rd world. here we dont know nothing about emissions testing and so on and so forth. in my country when you go to the police to get your car cleared they only test your brakes :P . ok ive recirculated my bovs. (pain in the ass to take the IC off. but the backfire stopped. thanks

Link to comment
https://www.sau.com.au/forums/topic/132186-got-fined/#findComment-2454015
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • GCG is a good company, they're a major distributor for Garrett in Japan as well.
    • Nah, OEM washer bottle and brake fluid reservoirs are fine I don't know what it is with the plastic that Mazda used, some plastics, like the washer bottle and brake fluid res are fine, and still look new after 20 years use, where as the coolant expansion tank, and PS reservoir, that I replaced with new OEM items when I first got the car, turned yellow and started getting brittle a few years later If the dirty yellow stained plastics didn't trigger me there wouldn't be an issue, but they did, much like the battery bracket....... Meh As for going back to work full time to support car stuff, nope, why, because I own a Mazda NC MX5, not a Nissan R series Skyline 🤣
    • I've never heard of CJ-motor, so can't advise you on them. I'd just go straight to GCG for a GCG highflow though. Seems no point to use a middleman. I'm somewhat surprised that the price on the CJ site is lower than the GCG retail price. Even though CJ would get a discount of some sort, you would hardly expect them to give up so much margin. Maybe the price is out of date? Having said that "I'd go to GCG"...when I did my highflow, I went to Hypergear. I did this https://hypergearturbos.com/product/rb25dethighflow/#tab-dyno-results with the R34 OP6 450HP profile. With the BB centre (extra $400) and intially with the standard boost actuator, but I eventually got him to send me the high pressure one when I got to the point of being able to actually use it. Ends up costing the same sort of money as the GCG highflow, but this is, of course, the turbo that I KNOW has a shorter length core and so moves the comp cover rearwards. The GCG apparently doesn't do that. My mechanic also swears by the GCG highflow, given that we have another turbo rebuilder who does something essentialy the same as theirs, using Garrett wheels. He says it stands up at really low revs and makes good power. I haven't pushed my HG highflow past ~240-250rwkW yet (should have a little more in it, but unclear how much) and it does have a fairly gentle boost ramp. OK, it's much better now that I have gotten my boost controller tuned up on it.  A lot of my earlier unhappiness was because I couldn't keep the wastegate flap as closed as it needed to be (including some mechanical issues). I'd still prefer it to boost up nearly as quickly as the stocker, and it certainly a bit slower than that. So maybe the GCG one is worth the first look (for you).
    • Ok thanks 🙂 I will higly consider this. Any "known" company for a good reviews and experience to send that off? Is that CJ-motor good one? Or go straight to GCG site? I need to use VPN to even find some of those "shops" let alone access them 🙂 
    • You can literally put in as much WMI as it takes to quench the combustion totally (and then back it off a little, obviously), and it will keep making more and more power. The power comes from the cooling effect of the water (and the meth) and the extra fuel (the meth, which also has massive octane). It is effectively exactly like running E85. One might be slightly better than the other, but they are damn close. But with either you can lean on the boost or the timing (or both) waaaay more than with just petrol and the results are similar. Here's the first thing I googled for an anecdotal bit of evidence. Can't access the attachment without being a gold member, but it is there for the getting if able to, or searched up elsewise perhaps. https://www.hpacademy.com/forum/general-tuning-discussion/show/wmi-vs-e85/
×
×
  • Create New...