Jump to content
SAU Community

Complete Fuel System Setup For Gtr

femno
 Share

Recommended Posts

femno Grand Master

femno

Posted
Posted (edited)

Hey Everyone,

Had big plans for the GTR that now arent going ahead :dry: , so time to get rid of some stuff: Basically i have what is needed for a decent fuel system setup!

All this stuff is brand new in original packaging, Never Used, just took it out to see how it all went together.

Siemens LOW inpedence injectors X 6 >> $110 each

Pro-fit Engineering Fuel rail kit for RB26 (Gold in colour) >> $270

Aeromotive Billet Fuel Pressure Regulator (2 Outlets) >> SOLD

As far as i know these injectors dont fit the standard rail because they are American made (different size) they fit straight into the manifold though. They still plug straight into the standard loom too (UNLIKE SARDS)!

The fuel rail comes with all necessary fittings and mountings, it has an inlet at each end and one outlet in the centre for a return line. Included in the fittings are optional Dash 6 and Dash 8 for the rail inlets.

Will post anywhere, at buyers expense. Can deliver in/near Eastern Suburbs if needed.

I Also have the ideal pumps for this setup. see sig link.

PM or call for quicker response

Thanks,

Mat.

0400 558 030

post-17897-1158977431.jpg

post-17897-1168855605.jpg

Edited by femno
Link to comment
https://www.sau.com.au/forums/topic/132293-complete-fuel-system-setup-for-gtr/
Share on other sites
`nigno Rising Star

`nigno

Posted
Posted

So im a bit confused... that rail is designed to house those american injectors? Or your just saying the injectors listed wont fit a stock GTR Rail in general... What I want to know is will that rail fit jap gear, coz ive got a set of 850cc SARDS with collars and im interested in the rail if they will fit.

femno Grand Master

femno

Posted
  • Author
Posted
So im a bit confused... that rail is designed to house those american injectors? Or your just saying the injectors listed wont fit a stock GTR Rail in general... What I want to know is will that rail fit jap gear, coz ive got a set of 850cc SARDS with collars and im interested in the rail if they will fit.

Yes i bought this as a setup, so the rail fits the rochester injectors. I dont see why it wouldnt fit your SARDS, its not a 'rochester specific' rail, its just for RB26...so i guess any aftermarket injectors would fit. Id say you have a bit to play with, you can use different seals etc.

And yes the rochesters just dont fit into the standard RB26 rail.

  • 3 weeks later...
  • 2 weeks later...
  • 2 weeks later...
femno Grand Master

femno

Posted
  • Author
Posted

This is a very cost effective setup...considering you can pay like 350 for a pair of denso type injectors this still works out cheaper even though you are buying a rail to suit, which looks great and has 2 inlets and a separate outlet....good for big hp GTR!

  • 3 weeks later...
  • 2 weeks later...
  • 1 month later...
  • 2 weeks later...
  • 1 month later...
  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • MBS206
      NC MX5

      By MBS206 · Posted

      Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Sorry I meant that we are building the EH for a client.
    • The Bogan
      Torana Lx Gtr Hatch, Lots Of Pictures

      By The Bogan · Posted

      LOL, when one "money pit" is never enough Noice, and excellent work mate
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I have more than enough digging, laying blocks, moving gravel, airrating, feeding and top soiling the grass, and setting up the veggie gardens growing some seedlings,  and then removing all the unused rock to keep me busy for the next few months at least,  hopefully the rain stops soon so I can get a few hours in this arvo, but, before that Sunday is washing day, is every body happy, you bet your life we are Nice country road day drives are a day off whenever I'm muscle sore from all the landscaping at the moment, but, more epic multiple day drives will start once the majority of the big jobs outside are completed
×
×
  • Create New...