Jump to content
SAU Community

Recommended Posts

Hi

Lately ive been feeling that my car is alot slower then when i first began to drive it. Now theres 2 things that could be due to this

1. Im used to the car so it feels slower

2.Compliance bastards tooks somethin off my car i didnt know about and didnt put it back on.

Im not sure what to think but really the car doesnt feel very impressive. What wer all ur opinions when u guys first got ur cars (namely R33 GTST). The mods on the car are full exhaust system, HKS airpod and HKS BOV. No boost mods etc.

Is it possible that i have a boost leak or somethin like that? Im graspin at straws here and its really buggin me cos the car really doesnt feel too good. Im upset : (

Any help appreciated.

Thanks, Dean

Link to comment
https://www.sau.com.au/forums/topic/13298-help-my-car-feels-so-slow/
Share on other sites

hah yup the initial bug does wear off alittle, thats when you flick the switch to 12psi and start the fun all over again.

As someone above suggestion grab a boost gauge and just make sure everything is still the same.

Or go for a ride as a passenger in someone elses GTS-T and you will realise how damn quick they still are :eek:

hey guys, i just joined this forum and i think its mad. ]

i just recently purchased a series II 97 gtst (actually im getting it tomorow or tuesday). i agree, i have driven the car about 3 times, and every time i drive it, it seems slower. i think we are just trippin. As i am a newby to skylines ive gathered a boost gauge will measure the amount of boost (psi??) in the turbo? is this right? cause i feel that my car (or soon to be) is lagging a bit. the only mods are hks intercooler (front piping and shit) and HKS air filter. should this boost my car a bit? should i reset the ecu? is it good for the car and wat does it do???

Cheers

Champinco

you should hear a slight tick at normal revs if it is there you would know also if you put ur hand over the exhaust and block the exhaust fully and if the engine stalls , NO Leak if it continues to run mmmmmm big leak, also you can tell by checking ur boost gauge if it reads below 7psi at full power you've got a big leak, if so expect to pay about $600 fitted get 2nd hand manifold don't pay more than $180 good luck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...