Jump to content
SAU Community

Recommended Posts

hey dudes.

im stuck with what turbo to chose on my car.

its an r32 gtst with the following mods:

FMIC

turbotech boost controller

bosch 040 fuel pump

K & N pod

Dr.Drift Remap running 14psi.

my aim is around the 190-200rwkw mark. i currently have 169rwkw with the above-mentioned mods.

im stuck in chosing these turbos:

Straight RB20 Turbo Highflow

Highflowed/Bored Turbine housing to fit larger steel/inconel Turbine wheel and shaft.

Highflowed/Bored Compressor Cover to fit larger alloy Compressor wheel.

This makes the Turbo Hi-Flowed both Compressor side and Turbine side.

The upgrade bolts directly back on the manifold and existing exhaust.

The housings are acid dipped and sandblasted back to new quality.

This is a journal bearing highflow and is capable of making 210-220rwkw and is rated to 18 psi max boost.

1 bar of boost is available from as little as 3000rpm.

Straight RB25 Turbo Highflow

Highflowed/Bored Turbine housing to fit larger steel/inconel Turbine wheel and shaft.

Highflowed/Bored Compressor Cover to fit larger alloy Compressor wheel.

This makes the Turbo Hi-Flowed both Compressor side and Turbine side.

The upgrade bolts directly back on the manifold and existing exhaust.

The housings are acid dipped and sandblasted back to new quality.

This is a journal bearing highflow and is capable of making 220-230rwkw and is rated to 19 psi max boost.

1 bar of boost is available from as little as 3400rpm

i wouldnt mind boost hitting me at 3000rpm, but then again, the rb25 unit would have more mid-range and top end, correct? for driveabilty and whatnot, what would be better suiterd to my needs, and mods?

any comments (good or bad) are welcomed.

thanks guys

jabba

Link to comment
https://www.sau.com.au/forums/topic/133351-turbo-choice/
Share on other sites

There is no difference between rb20 and rb25 hiflow. They get hiflowed to the same specifications. You can make boost come on earier, it all depends on intake setup, exhaust setup and state of the tune.

Link to comment
https://www.sau.com.au/forums/topic/133351-turbo-choice/#findComment-2471512
Share on other sites

There is no difference between rb20 and rb25 hiflow. They get hiflowed to the same specifications. You can make boost come on earier, it all depends on intake setup, exhaust setup and state of the tune.

There is actually a difference.

The compressor cover limits the size of the wheel that can be used in the R32 turbo.

The RB25 turbo and VG30 turbo have larger compressor covers thus larger wheels can be used that flow more air creating more power.

The R32 and R33 turbine housings are also different in size but do not affect power as much as the compressor cover size difference does as for an example a stage 1 and 2 wheel can be used in all 3 turbine housings- R32, R33, VG30 :O

Link to comment
https://www.sau.com.au/forums/topic/133351-turbo-choice/#findComment-2471893
Share on other sites

Paul is talking about the GCG highflow and is correct the internals are bored out to roughly the same size and rated at the same HP.

But everyone does there highflows different hence slides answer

where are you getting the highflow done?

cheers

Edited by Munna1
Link to comment
https://www.sau.com.au/forums/topic/133351-turbo-choice/#findComment-2472831
Share on other sites

you want to hit boost at 3 grand but are fitting a larger turbo?

those two don't match up and you'll likely add more lag.

specially choosing a gt3040r, don't expect much before 4500 ish

I had one on my r33 with the smaller exhaust housing to bolt on to standard manifold making full boost by 4000 to 4500 on 18 psi

Link to comment
https://www.sau.com.au/forums/topic/133351-turbo-choice/#findComment-2472889
Share on other sites

im leaning towards the rb20 hi-flow unit.

but will it run out of puff? spose it doesnt matter, coz im not gonna drag it in the near future.

sure the rb25 unit is more laggier, but it will obviously last longer.

i just want something with some get up and go,

i dont really want more than 200rwkw atm either.

so probably the rb20 unit.

Link to comment
https://www.sau.com.au/forums/topic/133351-turbo-choice/#findComment-2472906
Share on other sites

Yes I agree with Slide . I think he is telling you that the RB25 and VG30 versions use a larger diameter compressor wheel with a matching larger compressor cover . These would accept 70-71mm compressor wheels more easily than the covers on the smaller RB20 type compressors . This makes the RB25's turbo (housings really) a bit more flexible with compressor options . So in other words unless you want to stick with 60mm diametre compressor wheels ie dinosaur T3 wheels or a GT28BB cartridge the RB25 is the go .

Link to comment
https://www.sau.com.au/forums/topic/133351-turbo-choice/#findComment-2473552
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...