Jump to content
SAU Community

Recommended Posts

cheers mate, thanks heaps.....more if you could, its not suppose to be completely flush with the guard when looking from side is it????

Also is that a carbon fibre wing?or have you just put vinyl on top?if so id like to know how

looks very nice

which is lighter carbon fibre or fibreglass??

i think if your just buying the small wing... it should be level with the rear,though some people have varied designs.

the pics are of a mould we made from a boot with that lip on it then blended in... sits pretty flush with side guards..

its a full carbon fibre bootlid. weighs 4.5kgs i think my GTR bootlid is 26-28kgs so thats a big weight difference if you ask me.

here's a few more pics..

post-25424-1157892038.jpg

post-25424-1157892074.jpg

post-25424-1157892099.jpg

post-25424-1157892123.jpg

post-25424-1157892159.jpg

post-25424-1157892184.jpg

post-25424-1157892217.jpg

post-25424-1157892252.jpg

post-25424-1157892315.jpg

Edited by MrVspec
yeah.. made it myself.. along with the rest of the carbon stuff on my car..

i like the boot with that lip moulded in makes my 33 look tough..

Very tough indeed! I'm looking to buy a flat boot or drift wing..

Do you know if the flat carbon boots from carmate are any good?

As for the high level brake light.. just pull the one out of your stock wing and let it sit in your parcel tray! :)

Very tough indeed! I'm looking to buy a flat boot or drift wing..

Do you know if the flat carbon boots from carmate are any good?

carmate stuff is just fibreglass stuff with 1 layer if carbon... good for people on a budget that still want the carbon look... i've done repairs to so much crappy carbon products bought elsewhere though.. so if your buying products like that just take good care of them... keep them out of the sun as prolonged exposure to sunlight makes the resins they use go all funny colours...

hey r33madd, im selling mine on trademe,which i bought and havent used. Pm me for more details.Im selling to get a carbon version of both bootlid and wing lip.

Are you able to post up the link to the trademe auction or p.m the link, do you have any pics of it and how much do you want for itl??im very interested.cheers

will that bootlid + drift lip fit on a series 1 r33 skyline gtst coupe?or are the gtr boots slightly different

anyhow, how much we looking at for both?

the boot is $1650 in carbon or $880 in fibreglass....

both ?? it is just 1 its a replacement boot with that lip built onto it. was moulded like that...

and i'm sure all 33's are the same boot. GTR or GTST

oh and the boot hasn't seen the rain yet? but yeah it would pool up, just take it for a spin all the water will be gone in no time...

Edited by MrVspec
sent you a couple of pm's mate

cheers

PM's replied to

oh yeah just waiting on some other carbon to get here from france.... to match the bonnet and lower lip n stuff.. sold the other bootlid.

that pic shows how fat the GTR ass is... i love it

there's a few carbon goodies on her now, if your going to jamboree check it out, it will be in the Haltech stand on show.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...