Jump to content
SAU Community

Recommended Posts

I cant find a Blue Plate (nissan build plate) on my R32 GTST?? Only has a green compliance plate on firewall and aussie VIN etched on strut tower but not original jap VIN (which you need right?)

your vin might look like 6u90000er34002654 (posted earlier by someone) -- the original chassis number would be ER34-002654, which is what we put into FAST

Thanks Goofy,

Is there any chance u could tell me if this is a N1? I dont think it is but some1 claims otherwise

Eng no: RB26066194A

Vin: BNR32304039

Cheers

I'm not sure how to tell from the numbers (yet) - but apparently if you look on the side of the block and it says 24U its N1, if its 05U its standard

Edit: ok, KBNR32RXFS7 AA is the option codes it comes back with

It needs ZN at the end instead of AA to be a N1

Remix-: your pics not loading for me :)

Edited by Goofy[HSK]
Am I typing anything wrong for this to be run through FAST?

blockquote><p><a  href=http://img215.imageshack.us/img215/695/hnr32003113yf8.th.jpg' alt='hnr32003113yf8.th.jpg'>

If you put the option line in FAST first (KRNR32RGASLMAB) it then brings up another box asking for the vin.

It gets all the details about the car (gts-4, auto or manual etc.) from the option code - then just gets the production date from the vin. Colour codes didn't come up - i added them from your plate.

' date='23 Aug 2006, 10:16 PM' post='2433414']

your vin might look like 6u90000er34002654 (posted earlier by someone) -- the original chassis number would be ER34-002654, which is what we put into FAST

My aussie VIN doesnt have anything to do with the original chassis number.

MY aussie VIN is 6F9IMPORTTH9K**** (I left the last 4 digits out).

Why would they have removed the original blue plate? Is that even legal?

I guess I have no way of finding out anything about my car, will make ordering parts from nissan hard too!

My aussie VIN doesnt have anything to do with the original chassis number.

MY aussie VIN is 6F9IMPORTTH9K**** (I left the last 4 digits out).

Why would they have removed the original blue plate? Is that even legal?

I guess I have no way of finding out anything about my car, will make ordering parts from nissan hard too!

hmm... interesting - is there any other numbers on the firewall at all?

Hi guys. Never needed this thread until now but just want to check something. If someone could help out it would be much appreciated.

Can this software give part numbers for engine parts? Am I in the right place or is there some other software for this sort of thing?

I have been told that R34 GTR RB26DETT rods have the same part number as R34 GTT RB25DET. Could someone please confirm this for me or send me to the right place?

Thanks a lot.

Adam.

Hi guys. Never needed this thread until now but just want to check something. If someone could help out it would be much appreciated.

Can this software give part numbers for engine parts? Am I in the right place or is there some other software for this sort of thing?

I have been told that R34 GTR RB26DETT rods have the same part number as R34 GTT RB25DET. Could someone please confirm this for me or send me to the right place?

Thanks a lot.

Adam.

rodsbj6.th.jpg

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...