Jump to content
SAU Community

Recommended Posts

By the way who is organising this thing?????

I have a bit of an idear.... The hills have heaps of nice BBQ areas.. Bring a bbq and a footy.. it would be fun!

Lake Leshinultia is a good spot.. its in chidlow just up from mundaring.. and you hardly ever see cops there.... :) :) :) :)

  • Replies 104
  • Created
  • Last Reply

Top Posters In This Topic

Rose can ride with me if my girlies wont come with me :).

Here is the Map!!

check it;

SDU Perth Post Australia Day Cruise.

Meeting point : South Perth McDonald (corner of Burwick st & Canning Hwy)

Time: 9 am

Departure 9:10am

Destination: Victoria Park

Welshpool

Lesmurdie

Mundarling Weir dam

South perth

MAKE SURE YOU HAVE FULL TANK OF PETROL Just in case you don't get stuck in the middle of cruise. it is long drive...but it will be good.

Please follow correct Speed limit. and Do not drink and drive.

I will not take any responsibility of any accidents or anything for that matter, might/will happen during before and after the cruise! Cruise at your own risk. but he main thing is Have fun!

and I suggest you that have a look at the map before the cruise... 'Strong lives weaken left behind'

Route:

Exit McDonald by turn right to burwick st

then turn left at the 3rd traffic light to Hill View Tce

then turn Right on to Albany Hwy go straight

On to Welshpool road

Continue on Welshpool rd (it's long drive)

Turn Left to Glenisla rd (watch out for the sign this road Quite small)

Turn Right to walnut rd (stop and catch up) stop at Perth observatory

Turn 180 on to walnut rd then continue on to Lawnbrook rd

From Lawnbrook rd turn right to Canning rd and follow

then turn right to Mead st then straight to Mundaring Weir road (long nice drive to Mundaring dam)

Stop at the Mundaring dam (2nd car park) have much larger space to park our skyz.

Also for late arrivals we will stay at the Mundarling dam for while have lunch and photo shoots...etc (weather Permits)

exit car park by turning right follow Mundaring weir road.

(Follow the street sign to get on to 'Great Eastern Highway')

from Mundaring weir road

Turn right to maddock st

then turn left to Jacoby st

then turn right to Nichol st

Turn Left on to Great eastern Hwy. ( we will stop here for slow drivers )

Follow Great Eastern Hwy to perth

Then Last stop at the South Perth James Mitchell Park.

Originally posted by adam 32

what time are youn expecting to finish?

cos ill be on the road by around 12.... where will you be then?

it will be depends on people but I would say we till be at mundarling or on the way to Perth south perth....for lunch

cheers

Joe :)

Guest Rhino

I think we should try and organise to be at one place at a certain time, that way anyone who can't make the start can be sure of meeting us somewhere along the way.

I cant remember how long it took us last time to get to Mundaring, but that is probably the best place to organise to be at by 12 or whatever??

I dont think its gonna take 3hrs to get from maccas to south perth:rolleyes:

Wont be coming for this one fellas due to the fact there is no way Gradenko will wake up b4 2pm and im not gonna drive myself in the 84' corrolla.

Have a good 1 fellas:D

Can't please everyone Adam

If Joe changes the time someone else will have a whinge meaning others will drop out so he's in a loose / loose situation.

It's unfortunate that you can't come but hopefully we'll see you later

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...