Jump to content
SAU Community

Recommended Posts

Hi,

I live in Huntsville, Alabama in the US. I will be importing an R32 soon and want to know which would be a better car. I plan on, if I get the GTS-t, putting in an RB26DETT and eventually getting it up to GTR looks. I will primarily be drifting and heading out to the local drag strip. Which car would be a better buy, an R32 GTR or an R32 GTS-t? The GTR would cost me more at first, but will be AWD. The GTS-t would cost me less at first, and I can upgrade in stages, but will be RWD. I assume that having it RWD would be better for drifting, as AWD is inteneded to reduce traction loss, thus hindering ability to drift. However, I have read that with the GTR's AWD system, it only gives the front wheels power if it detects loss of traction in the rear wheels, and it can be locked in either AWD or RWD modes. Is this true? I would just like some simple advice on the subject.

Thanks

Mazikowski

EDIT: Just on a side note, I am about 6' 2" tall (so around 2m?). How would headroom in the car be for me? Would it be overly tight?

Edited by Mazikowski
Link to comment
https://www.sau.com.au/forums/topic/133936-gtr-or-gts-t/
Share on other sites

well it really depends.. if your going to use it more for drift or drag.

it will be ALOT cheaper to go the route of the GTR. Running conversions and doign things in stages will cost you an arm and a leg in labour/time/parts

plus.. who doesnt want a gtr :P

Link to comment
https://www.sau.com.au/forums/topic/133936-gtr-or-gts-t/#findComment-2483860
Share on other sites

Go the GTR! You can easily turn off the AWD by pulling a fuse or putting in a switch to turn it on or off.

It will be more expensive initially but you will spend more to get the GTSt to anywhere near the same dynamics in the long run.

If it does not have a sunroof you should be right height wise or you could fit lower seats if not.

Thought you guy's could not have Skyline GTR's there in the land of the free :P

Link to comment
https://www.sau.com.au/forums/topic/133936-gtr-or-gts-t/#findComment-2483956
Share on other sites

well, you cant import them really because of laws in states with major ports, but if you import the car w/o engine + engine separate, it can be done, just assemble it in the destination state and off you go... besides, it helps to have some connections :dry:

I should be able to get a GTR for around < USD25k or a GTS-t for < USD15k

plus.. who doesnt want a gtr :O

this is true... OH HOW TRUE THIS IS!!!! lol, sorry, had to get that outta my system

Edited by Mazikowski
Link to comment
https://www.sau.com.au/forums/topic/133936-gtr-or-gts-t/#findComment-2484197
Share on other sites

If it is SPECIFFICALLY for drift, I'd go GTS-T. Lower purchase price, less weight (AWD hardware is HEAVY!), cheaper to replace parts and body panels (probably).

If it's a powerful multipurpose drag/track street car, I'd go a GTR.

I'm 6ft4 (with a heavy build), and I fit in my R32 GTS-T just fine. But for enthusiastic driving, I'd budget for a new drivers seat and steering wheel - the standard items are under and over sized (respectively) and are pretty much useless for people my size! The R32 GTR seats are apparently much better, but alas I have never driven one and hence cannot comment.

Link to comment
https://www.sau.com.au/forums/topic/133936-gtr-or-gts-t/#findComment-2489230
Share on other sites

If it is SPECIFFICALLY for drift, I'd go GTS-T. Lower purchase price, less weight (AWD hardware is HEAVY!), cheaper to replace parts and body panels (probably).

If it's a powerful multipurpose drag/track street car, I'd go a GTR.

I'm 6ft4 (with a heavy build), and I fit in my R32 GTS-T just fine. But for enthusiastic driving, I'd budget for a new drivers seat and steering wheel - the standard items are under and over sized (respectively) and are pretty much useless for people my size! The R32 GTR seats are apparently much better, but alas I have never driven one and hence cannot comment.

Alright, thanks for the info on sizing. I will most likely be using it for both and maybe even some... I guess it would be like circuit? ... racing. Knowing that I can switch between AWD and FWD with a switch ( gotta install first, I know ) makes me wnat the GTR, a bit more power and better car for the most part. Now, to get the money >_<

Thanks

Mazikowski

Link to comment
https://www.sau.com.au/forums/topic/133936-gtr-or-gts-t/#findComment-2492245
Share on other sites

Id go the gtst personally, cheaper parts and parts are easly found. with the extra money you will have left if you bought a gtst, you could put it back into your car. dont let the GTR badge fool you I have seen plenty of gtst beat gtr in races on the street and personally, there's not substitute for hanging that arse out when you feel the need to. :O

Link to comment
https://www.sau.com.au/forums/topic/133936-gtr-or-gts-t/#findComment-2492712
Share on other sites

why would it be less expensive? I would end up putting an RB26 in most likely.

I will have to do some more research into it, but I still have a while to go before I would be fully deciding.

why bother with the rb26, go the rb 30, with rb25 top end, its stronger and can produce big hp. and go 1 big single turbo rather then twin turbo.

with the bigger engine, and reduced weight (not having a GTR) = :)

Link to comment
https://www.sau.com.au/forums/topic/133936-gtr-or-gts-t/#findComment-2493346
Share on other sites

but how hard would it be for me to get a 30 with rb25 top end? Like I said, It will take some research... thanks for the advice all the same

::EDIT::

Although it has a larger displacement than the RB26DETT, maximum possible horsepower is less, as the RB30 block lacks the RB26 block's internal cast-in bracing, and consequently cannot rev as high due to harmonic issues at ~7500RPM. To compensate, the RB30DET produces more torque at lower revs.

from http://en.wikipedia.org/wiki/Nissan_RB_engine#RB30

Edited by Mazikowski
Link to comment
https://www.sau.com.au/forums/topic/133936-gtr-or-gts-t/#findComment-2495813
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah, OEM washer bottle and brake fluid reservoirs are fine I don't know what it is with the plastic that Mazda used, some plastics, like the washer bottle and brake fluid res are fine, and still look new after 20 years use, where as the coolant expansion tank, and PS reservoir, that I replaced with new OEM items when I first got the car, turned yellow and started getting brittle a few years later If the dirty yellow stained plastics didn't trigger me there wouldn't be an issue, but they did, much like the battery bracket....... Meh As for going back to work full time to support car stuff, nope, why, because I own a Mazda NC MX5, not a Nissan R series Skyline 🤣
    • I've never heard of CJ-motor, so can't advise you on them. I'd just go straight to GCG for a GCG highflow though. Seems no point to use a middleman. I'm somewhat surprised that the price on the CJ site is lower than the GCG retail price. Even though CJ would get a discount of some sort, you would hardly expect them to give up so much margin. Maybe the price is out of date? Having said that "I'd go to GCG"...when I did my highflow, I went to Hypergear. I did this https://hypergearturbos.com/product/rb25dethighflow/#tab-dyno-results with the R34 OP6 450HP profile. With the BB centre (extra $400) and intially with the standard boost actuator, but I eventually got him to send me the high pressure one when I got to the point of being able to actually use it. Ends up costing the same sort of money as the GCG highflow, but this is, of course, the turbo that I KNOW has a shorter length core and so moves the comp cover rearwards. The GCG apparently doesn't do that. My mechanic also swears by the GCG highflow, given that we have another turbo rebuilder who does something essentialy the same as theirs, using Garrett wheels. He says it stands up at really low revs and makes good power. I haven't pushed my HG highflow past ~240-250rwkW yet (should have a little more in it, but unclear how much) and it does have a fairly gentle boost ramp. OK, it's much better now that I have gotten my boost controller tuned up on it.  A lot of my earlier unhappiness was because I couldn't keep the wastegate flap as closed as it needed to be (including some mechanical issues). I'd still prefer it to boost up nearly as quickly as the stocker, and it certainly a bit slower than that. So maybe the GCG one is worth the first look (for you).
    • Ok thanks 🙂 I will higly consider this. Any "known" company for a good reviews and experience to send that off? Is that CJ-motor good one? Or go straight to GCG site? I need to use VPN to even find some of those "shops" let alone access them 🙂 
    • You can literally put in as much WMI as it takes to quench the combustion totally (and then back it off a little, obviously), and it will keep making more and more power. The power comes from the cooling effect of the water (and the meth) and the extra fuel (the meth, which also has massive octane). It is effectively exactly like running E85. One might be slightly better than the other, but they are damn close. But with either you can lean on the boost or the timing (or both) waaaay more than with just petrol and the results are similar. Here's the first thing I googled for an anecdotal bit of evidence. Can't access the attachment without being a gold member, but it is there for the getting if able to, or searched up elsewise perhaps. https://www.hpacademy.com/forum/general-tuning-discussion/show/wmi-vs-e85/
    • Dang, those BBS are so nice! 
×
×
  • Create New...