Jump to content
SAU Community

Recommended Posts

Hmmm, could work its way off, might be tight fit now but on a warm day travling along the freeway at 110 km/h gearbox gets hot. But I'm lazy so I'd probably do the same

Yeah, i know what you mean. I was actually a bit more concerned about a circlip working its way off a groove that i fabricated. The one that broke in my car didnt move at all. The shaft actually snapped inside the sender assembly. Too late now anyway; i put the box back in today.

Shaun.

  • Replies 188
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Hmmm, could work its way off, might be tight fit now but on a warm day travling along the freeway at 110 km/h gearbox gets hot. But I'm lazy so I'd probably do the same

Considering the circlip design used on the r33 drive is the odd ball of the family and the rest of the drives use an interference fit with some kind of adhesive i think you'll be fine.

Mine hasn't caused any problems yet and it regularly sees track work and speeds in excess of 180km/h.

I started my car today and noticed that the speedo needle was jumping slightly at about 20km/hr (thats as fast as i could go while the car was on stands). Im a bit dissappointed about this as i think it might suggest that the gear might be under unwanted force or something. What do you guys reckon?

There arent any sharp bends in the speedo cable either, which would also make the needle jump.

Shaun

  • 3 weeks later...
The standard x-member bolts up to it.

3 bolts + 1 nut + locktight in total are required.

Sweet, so just two plates, and stock R32 x member and your done.

So your pritty much just conecting the gear box to one of the original body bolt holes and using the plates for extra strength.

Sweet, so just two plates, and stock R32 x member and your done.

So your pritty much just conecting the gear box to one of the original body bolt holes and using the plates for extra strength.

Thats it.

The plate is there for 2 reasons.. To space the box down a touch so it doesn't foul the tunnel and to provide a little extra stability to the xmember as when you only use one of the origional bolt holes the back of the xmember hangs off the floor pan. Thats where the plate provides support for it.

Almost finished the conversion today, only have to put the speedo sender in and extend a wire for one of the sensors that plug into the box.

For the plates i chose not to space the gearbox down as it wasnt close to fouling and i didnt want to put the box on any bad angles.

I cut away some of the crossmember and fitted the plates underneath. I also welded them in, i then trimmed the bits i cut out and refitted them in also by welding. I then ground them back for a nice look and painted it all black. Pics tomorrrow :D

The tailshaft left this monring for universal driveshafts in geebung (qld) the guys did a perfect job swapping over the yokes, and obviously balanced it before it was retured at 445 today :/ very happy with the service and price which was $175

Thats it.

The plate is there for 2 reasons.. To space the box down a touch so it doesn't foul the tunnel and to provide a little extra stability to the xmember as when you only use one of the origional bolt holes the back of the xmember hangs off the floor pan. Thats where the plate provides support for it.

Feel like drawing it up with measurments so I can copy it?

I wont be dropping my engine and gearbox in till late april early may so I wont be able to verify if your plate fits the same on each car but its worth checking so future people dont have to messure their own.

Thats strange as I found the top of the gearbox snagged the floor pan with the xmember around 2mm away from the floor pan. So I was forced to space it away. :S

Did you massage the floor pan a touch?

Hey joel,

i have the xmember bolted to the car, no spacing. I didnt touch the tunnel/floor pan at all, the box fitted in great. I do have a hoist and gearbox lifter tho :)

Edited by 2630GTS

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I get that taking off the head is best but that's a bit much for "just" valve seals. I was just under the impression that one would be able to rotate to TDC and be able to temporarily drop the valve without losing it and effectively having to remove the head to then recover it. I never knew people actually pushed rope into the cylinder to do valve seals hahaha So just to confirm, just going to TDC will not work? In that case I know when I do valve seals I'll maybe just remove the head and do some other things while I'm there, or just wait until I do an engine build.
    • The old approach was to fill the cylinder/chamber with a length of rope pushed in through the sparkplug hole. The new approach is to connect compressed air to the sparkplug hole and fill it with enough pressure to push the valves up. Doing either of these things with the head on and the engine in the car is a lot less pleasant than doing it properly.
    • Can't you put the pistons to TDC and then do the valve seals? Or will the drop down too far to pull them back up?
    • One thing I can tell you is, do it properly the first time. If you encounter unexpected problems just let the car sit for a week or two if you have to get some other parts or figure stuff out.  I'd have said go and use as many OEM parts as possible but since you want to change the turbo later on a custom kit is probably the better choice. Since I have no experience with RB25 just compare parts diagrams and images before buying a line kit and it should be easy to see if it has everything you need. Amayama has very good parts diagrams and part number lists, that is what I used a bunch to figure out what I might need. And don't forget to plan ahead and possibly renew other stuff that's easy to get to while you're in there doing the turbo lines. Happy wrenching
    • Update 4:   Hi all, good news. Engine is running and all the gaskets and seals seem to be working as intended. No leaks so far, even the JB Weld seems to hold. I flushed out the old coolant a few times and put in fresh coolant, not Nissan stuff, I decided to try the Ravenol Protect FL22, they claim it works for a wide variety of JDM cars and the opinions on it by some people were pretty good. And it has the nice poison green color! And man am I glad I bought a coolant system tester earlier this year, vacuum filling works wonders on this engine. I can definitely recommend this to anyone still doing it the old school way. All you need is compressed air supply. Will have to do a small test drive as soon as I can, I removed the gauge cluster again as the tacho needle was still bouncing around a bit but it was much better than before already.  I also found some cracks on all 4 tires inner and outer sidewalls. Apparently these tires should 't be parked on for extended periods or be kept under 0 degrees during storage, which I did not know. Clearly the previous owner didn't look into those details either, he probably bought them just cause they are cool semi-slicks. I'm just wondering how tf I am supposed to reach 30-80 degree tire temperatures on the public road consistenly, these tires were never going to work for my use case. I'll probably order Continental SportContact7 ones as these are the best allround summer tire available right now and I don't think I'll need anything crazier for now. Do let me know if you have experience with various tires and which ones you recommend.
×
×
  • Create New...