Jump to content
SAU Community

Mazda 3 Mps

Noel

By Noel,
in General Automotive Discussion

 Share

Recommended Posts

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

nsanity Rising Star

nsanity

Posted
Posted
i cant wait to see one of those maxda 3 turbo's worked too 250-300kw

FAAAAAAAAARRRK!

I wouldn't.

220kw is about the limit for a front wheel drive. Even prior to that you start to see hideous amounts of torque steer (plant your foot, go left!).

Its well known in the UK where they have many "hot" front wheel drives sold from manufacturers.

RWD and adjustable AWD for the win.

GT-R32 Grand Master

GT-R32

Posted
Posted
Haven't driven either of them, but independent testing shows the 3 MPS is in fact quicker...

At least in gear I reckon a 3 MPS would take off. The launch of the 6 MPS gives it the 1/4 time advantage. Roll on would be a different story.

Revhead Grand Master

Revhead

Posted
Posted

Karen and I took an M3 (just for you Daveo :D ) MPS for a drive a week or two ago, and I have to admit I was more than a little impressed. I was a lot more impressed than I expected to be actually. That said, FWD dynamics don't really do it for me, and it apparently has a stability control thing in it, so I deliberately botched a corner entry to test it and it happily understeered towards the side of the road lol. In the rest of the corners it seemed to hang on quite well though, maybe they've tried to make the stability control not too intrusive? Powering out of a corner was frustrating but something I could live with given the rest of the package.

I thought the interior was fairly nice, the seats and pedal placement were good, the wheel is adjustable for reach and tilt and the dash is fairly easily readable. My only gripes were that some parts of the interior felt a bit cheap, and the clutch was really grabby, nearly as grabby as my old 5 puck brass button - it went from nothing to fully engaged in probably 10mm of pedal travel. This is fine if you're expecting to do a fair amount of track work or hard driving, but for a vehicle that I personally see as a quickish road car rather than something I'd be wanting to take to the track all the time, it's a bit annoying.

Gordo, peak power to weight doesn't tell the whole story, these things make stupid amounts of torque from 3k up until nearly the redline. In gear they are really quite impressive :(

GT-R32 Grand Master

GT-R32

Posted
Posted
but look at the 294nm of torque @ 4800rpm in R33 compared to 380nm @ 3000rpm in MPS...not that i would choose one over my R33 but its quite impressive

Which indicates the Mazda 3 has a higher average power over the rev range.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      If there's enough meat in the housing where you want to put the M12 adapter, then do it, but be aware that if/when you f**k that up you'll probably be repairing it before doing anything else. I'd just drill it out and tap ina 1/4" thread. No need for rocket surgery when the next most obvious thing will do. You could throw a 1/4 x 1/8 bush in there and use the same fitting you intended to use.
    • GTSBoy
      RB26DETT Sketchy boost mod?

      By GTSBoy · Posted

      Not this But this  
    • Murray_Calavera
      What should I do next to hold the head on

      By Murray_Calavera · Posted

      Is the only issue that the oil catch can is getting filled on hard runs? I'd be thinking more about oil control issues rather then the head lifting, especially as you aren't seeing spiking in the coolant pressure.  Do you need restrictors in the head, or better drains from the head? Does the sump need venting to the catch can?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      Tried to make 1/8npt threads into compressor house of the turbo for my EBC. Threads got fu#ked and ended up with and elongated hole, so I do have good amount and nice threads 90% of the hole but 10% I only had 1-2threads there and rest of it is flush on that side of the hole.. So my idea is to do M12 x 1.25 to AN4 with braided lines instead of 1/8npt to 4mm vacuum silicone hose.  and hopefully get a better thread. M12 is quite big and AN4 is a little bit bigger than 4mm (4.9mm inner diameter braided PTFE hose). but this should work. Thoughts? Otherwise I will weld and adapter onto the turbo.   
    • Duncan
      C34 RSFour V Build in the US

      By Duncan · Posted

      Looks great, I hope everything is working well after all that time!
×
×
  • Create New...