Jump to content
SAU Community

Recommended Posts

:sorcerer: EVERYTHING HAS BEEN SOLD :sorcerer:

:) R33 GTR and GTS4 PARTS for sale :dry:

INDIVIDUAL PARTS ARE ON THE MARKET

Rb25/30 engine partially assembled

Block de-burred cleaned honed

Hypertec Hypereuretic pistons and rings fitted

Kings bearings fitted

Re-sized rods polished and de-burred fitted

Drilled and tapped for rb26 sump adapter plate fitted

Sump half converted

Adapter plate with all hardware and instructions

Os gieken twin plate clutch

Head

Reconditioned

Blocked and tapped (25/30 conversion)

Apexi 270deg 8.7mm lift cams new fitted

All electrics

$4200

New Parts

Intake

Q45 90mm throttle body $200 (SOLD TO legend01)

Q45 afm with plug $200

Greddy style intake new $400

Intake pipe with all reducers $50

Apexi 3” pod filter $50

700x300x105 intercooler with all piping and silicone connections/reducers $350 (HOLDING FOR outie)

Hks style sequential bov new $80

Xs power bov $60

2x 40mm waste gates with pipe new $70 ea

50mm waste gate new $90

Apexi power fc with hand controller new $900 (HOLDING FOR outie)

Malpassi 1.7:1 rising rate regulator $150

Bosch 040 fuel pump $170

Venom 800cc injectors new $700

Splitfire Coils new fitted $550

Exhaust

T70 turbo new $600

T70 oil lines new $200

Top mount manifold $350

3” dump pipe new $190

3” cat back new $450

4” Magic cat new $200

Wheels

Lenso Muse 19”x8” new $900 (HOLDING FOR outie)

Nangkang 235/35ZR19 tyres new $900

EXTERIOR

Trust style front bumper $400

Nisom clear side indicators $70

gtr badge set $130

Various gtr and gts4 parts available.

left front guard $200

right front guard $200

Standard gtr suspension $200

Fuel pump $50

Power windows $150

Central locking $50

climate control display $180

right hand headlight $100

Left hand head light $100

rear lights $150

diff $800

drive shafts X 4 $450

rear glass (tinted) $100

boot $300

Drift Rear Wing $400

Type m side skirts undercoated $150

rear pods $50

Type m rear bumper undercoated $100

4wd PUMP system $300

boost controller Dual stage $100

Complete dash $500

Gtst instrument panel $150

Gearbox $1100

LHS door with mirror $200

RHS door with mirror $250

floor mats $50

rolling shell with compliance plates and gtr rear guards fitted $3000

Seats $300

Gtr instrument panel and 3 gauge center setup with carbon fibre $300

Hicas computer $50

Fuel pump computer $20

attessa ECU $300

windscreen wipers $50

chassis brace $80

Prop shaft $250

Clutch slave cylinder $100

Brake master cylinder and booster $200

Alternator $100

Sway bars $175

Fuel level sender $50

Fuel tank $150

Fuel cap $10

Power steering pump $150

Power steering rack $100

Front door trims $100

Centre console $100

Gear selector plastic surround $50

Rear parcel shelf $60

Dash clock $30

Indicator stalk $100

Windscreen wiper stalk $50

Steering column $200

Carpet $60

MORE PARTS AVAILABLE JUST ASK.

parts___pix.doc

Edited by REDMAN8
  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

:( REMEMBER GUYS

COULD YOU PLEASE PM ME WITH OFFERS FOR PARTS/PACKAGES LISTED SO THAT I CAN KEEP TRACK.

AND THE WHOLE LOT IS FOR SALE UNTIL THE 25TH SEPTEMBER.

ONLY THEN WILL PARTS BE ABLE TO BE PURCHASED. :laugh:

THANK YOU

REDMAN8.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...