Jump to content
SAU Community

Recommended Posts

hey guys, ive been trying to get my car started for the past 2 days and still no go. first i thought it was the battery because it was dead and after i had charged it, it wouldnt take any load. i then changed the battery and still the same prob.

anyone ever had a problem like this before. to me it seems like its electrical because its firing but kinda sounds like something is cutting it off as it starts.

Thanks, Mike.

Link to comment
https://www.sau.com.au/forums/topic/134828-car-wont-start/
Share on other sites

Does a fuel pump have a fuse?Did you check for petrol? :laugh::laugh:

Sound like an electrical short ...check coils and plugs.

Then check if you can hear your fuel pump working.

Also sounds like a blown fuse...check your fuses.

Link to comment
https://www.sau.com.au/forums/topic/134828-car-wont-start/#findComment-2506619
Share on other sites

failing that, disconnect the AFM and then start it up with half throttle. If that works, you have a dead AFM.

Turn it off afterwards, cause you shouldn't run it for long like that.

Edited by RANDY
Link to comment
https://www.sau.com.au/forums/topic/134828-car-wont-start/#findComment-2507319
Share on other sites

Could be no vacuum in the aac valve, at the back of the plenum near the bulkhead

if it sticks open it can cause a vacuum leak at low revs and cause a stall, or it could stop it from starting at all.

Hey mate, are you saying that my aac valve could be stuffed or something in my plenum?

Link to comment
https://www.sau.com.au/forums/topic/134828-car-wont-start/#findComment-2510019
Share on other sites

Heres a DIY from these forums

Normally this wouldn't cause your car to not start unless there was consistently no vacuum, however I recently had some issues with Idle hunting and occasionally the car firing but not starting, and this seemed to solve my problems.

http://www.skylinesaustralia.com/forums/in...110431&st=0

Edited by Mike_
Link to comment
https://www.sau.com.au/forums/topic/134828-car-wont-start/#findComment-2512160
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...