Jump to content
SAU Community

Recommended Posts

Hi Guys, I have spend a LONG time tonight trying to get my car into HICAS check mode to be able to insert the second shim from the Tomei HICAS Lock Kit.

Is there any suggestions as to why it would be doing this? I have checked the connections in both the boot and in the engine bay and they are fine... The hicas light comes on when the ignition is at the on position (but not started).

Is there another way of doing it? If I were to unbolt the rear steering arm from the hub assembly, would that allow enough movement at the required point?

Thanks for your help!

Todd

Link to comment
https://www.sau.com.au/forums/topic/135383-cant-get-hicas-into-check-mode/
Share on other sites

Hi Guys, I have spend a LONG time tonight trying to get my car into HICAS check mode to be able to insert the second shim from the Tomei HICAS Lock Kit.

Is there any suggestions as to why it would be doing this? I have checked the connections in both the boot and in the engine bay and they are fine... The hicas light comes on when the ignition is at the on position (but not started).

Is there another way of doing it? If I were to unbolt the rear steering arm from the hub assembly, would that allow enough movement at the required point?

Thanks for your help!

Todd

Anyone?

You can install the shims without going into check mode but it means that you have to undo both sides of the rack.

It's a bit of a pain in the arse way of doing it, but when your hicas is already stuffed the bastard just doesn't want to play (atleast mine didn't) :laugh:

You have to remove one tie rod completely to get enough of a grip on the rack itself to crack the other side. Then you can just back that one off a bit, slip in the shim, tighten it up, and then put the other shim on before refitting the tie rod.

OK, so I have managed to remove one side but due to how thin the inner bolt bit (on the side I have removed) is the spanner/shifter keeps slipping off (as it only has 2 sides).

I put the tie rod back on to put pressue on the spanner to stop it from coming but I have nearly rounded it!

Any suggestions? and don't say take it to a shop, I have already thought that! :) How funny is it when you are under your car thinking I would pay someone $50 to do this but when you have done it you are stoked you have saved yourself $50! ha ha ha

hicas1nk2.jpg

hicas2go9.jpg

hicas3qe9.jpg

Thanks,

Todd

Just use a 12 volt power source on the connection on the round part, there are three tabs, one is left, one right and the middle I think is negative (dont quote me on that), When I did it I used sheilded aligator clips to work it out and no need at all for the hard ways, works a treat, the wheel alignment guy checked all my nuts and bolts as I left the rubber boots loose and he zipped tied them after.

are u talking about the rack because on the r33 they are electric but on the 32 they are hydraulic, so cant use the power source?

EDIT

understand what they were talking about now! makes sense.

Edited by GTR1993

DONE!!

OK this is what I did...

- Unplug the HICAS plug in the engine bay

- Strip a section of the wires either side of the center (earth) wire

- Plug the plug back in

- Start the car

- Get someone else under the car ready to slip in the shim (as it will move back in to place in a second or two...)

- Touch a wire to the + battery terminal and touch it on the bare wire on one of the stripped wires FOR A SECOND OR TWO... (one is left, the other right)

- If you got the correct wire, it shoud have moved and created enough of a gap for your mate to slip the shim in! If you got the worng one, you will need to turn the car off for a sec and try again as it wont work a second time...

- Once you have both in, tighten them up, unplug the plug and make sure you connect up the electric module correctly! (I got one wire around the wrong way and my bake lights turned on when ingition was on and the fuel pump when when I put my foot on the brake... - WHOOPS :nuke: )

Hope that helps!

Todd

Edited by CATKICKER

word...

for future reference, to get the other side off, notice in the bottom picture you posted there is a gold screw thingo. Unscrew this with a shifter and remove it, then the part of the rack that the tie rod screws into will be visable. You should be able to slip a 17mm oe spanner onto it to stop it turning when you undo the other tie rod

word...

for future reference, to get the other side off, notice in the bottom picture you posted there is a gold screw thingo. Unscrew this with a shifter and remove it, then the part of the rack that the tie rod screws into will be visable. You should be able to slip a 17mm oe spanner onto it to stop it turning when you undo the other tie rod

Well that makes sence!! grrr

Oh well, this works too :laugh:

Car is in getting alignment so will see how it goes!

Cheers,

Todd

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...