Jump to content
SAU Community

Recommended Posts

got some boys bringing their pride and joys out on october 14th (saturady) to head for a cruie, either geelong or down the mornington peninsula. Puttin out an invite to any other skyline drivers who are interested in joining in. Its NOT an OFFICIAL cruise but more of a fun day out to meet other enthusists.

Meeting at 10:30am at Bell st Mc Donalds (cnr bell st and st geoges rd preston)

cruise to either side of peninsula, (location tba) pick a location to stop and kick back

then cruise back home

WILL BE WEATHER PERMITTING. SUNNY DAY ONLY WITH NO RAIN

Cheers

post-31466-1159067010.jpg

post-31466-1159067022.jpg

Link to comment
https://www.sau.com.au/forums/topic/135741-skyline-cruise-to-geelong/
Share on other sites

hey Andrew, do you drive a blue wrx with white mags & cooler?

Nah he works in Safeway (do not see how he can afford the insurance)

Mine's dark blue, about the only wrx in Geelong with a SAU sticker

Andrew :D

that blue rex with the white wheels and cooler is my mate, pretty quick for minimal mods

nah man dealer (no mass wing, not a poser)but did have some wing on it, need 2 get holes filled soon . here it is:

post-31419-1159701541.jpg

Edited by tigr33

You could stop in that park just outside geelong (on way to drysdale) or go down to portarlington and get some fish n chips type thing. Then cruise around the peninsular from portarlington past St leonards etc.

St Leonards - Drysdale direct used to be a really shit road, full of potholes.. got 2 flats in a week once!! Dont know if it's better now though.

From memory it's about 30mins from geelong to portarlington or st leonards.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...