Jump to content
SAU Community

Recommended Posts

Thought I might open this up with a list of mods, wont put in a future list coz I don't think the page is big enough :laugh:

Bought the car with Pod, Teins, Nardi, 16in AVS, Newly transplanted Rb20 ('uknown' k's), blitz boost gauge and around 160,000k's on the clock. Now it has the following mods and ~208,000k's on it:

  • Apex Pod (Replaced the K&N oily one that came with the car)
  • 40mm Alloy Rad
  • Uras Bodykit (Now sold and back to standard)
  • HKS Oil Cooler
  • Rainbow Sox
  • Extreme HD Clutch
  • Bleed valve @ 0.8Bar
  • Bride Zeta
  • Reinhard Catback
  • Speco Water temp gauge (soon the be replaced with Defi Din gauges)
  • Kaaz 2 way diff

Here are some pics. will get more when its lighter, stupid video cam takes shitty stills in low light.

post-18824-1159173438.jpg

Interior when I bought the car.

post-18824-1159173495.jpg

Engine bay prior to 40mm Rad going in.

post-18824-1159315520.jpg

With 40mm Rad.

post-18824-1159173464.jpg post-18824-1159173998.jpg post-18824-1159174178.jpg

With Uras attached.

post-18824-1159173354.jpg

Bride Zeta.

post-18824-1159173201.jpg post-18824-1159173242.jpg post-18824-1159173274.jpg

Reinhard. Complete with removable mufflers and silencers (excellent for street use).

Here is a vid of my drifting with the exhaust fitted:

That's all for now. Konect.

Edited by konect
Link to comment
https://www.sau.com.au/forums/topic/136000-konect-1990-cefiro/
Share on other sites

NICE VID!

what is the tune like on it? sounds a bit laggy? love the RB sound though!!

Nah probly more my driving that makes it laggy. Was my first run for the night so I was a bit out of practice, later on I started keeping the revs up while on handbrake so it wouldn't bog down, then slamming third for the last corner.

Tune is the normal jap tune (rich as a mofo!) and comes on about 2.5k revs which is about normal. Not too bad to drive :)

Thanks for the comments :yes: Will get better footage next month.

nice car mate, it reminds me of the one in bigx in hpi9 (except yours is better), i cried when i saw what they did to that car :nuke: ..... and the laurel :):)

lol yeh i have that vid! OH my poor car, at least it doesnt get rolled on its roof...yet, touch wood :D

Edited by konect
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...