Jump to content
SAU Community

Recommended Posts

Hi,

When should you use a turbo timer?

I have a turbo timer installed (standard car running standard boost) and i only use it when i give the car a bit of a thrashing. Normal driving i dont bother with turbo timer.

is this wise? or should i always use it?

cheers

Link to comment
https://www.sau.com.au/forums/topic/136806-turbo-timer/
Share on other sites

you only need to use it when you've been on boost just before you're turning the car off.

If you drive normally and stay off boost when you're getting close to where you're going, you dont need to use the TT as the turbo hasn't been doing anything

Link to comment
https://www.sau.com.au/forums/topic/136806-turbo-timer/#findComment-2543148
Share on other sites

TTs are after-market gadgets. If Nissan had wanted you to use one, they would have installed them as standard items.

TTs are generally for idiots who can't control their right foot during the last km of any trip, and are then too impatient to wait with the car for a minute while the turbo cools down a bit.

Link to comment
https://www.sau.com.au/forums/topic/136806-turbo-timer/#findComment-2543233
Share on other sites

I dont have a TT...

...I just take it easy as im approaching my destination, and usually wait about 15-20 odd seconds (Usually spent closing windows, sunroof, side mirrors) before switching it off....but i never let it sitting idle as you'll end up trapping a bit more heat due to no/less airflow.

Link to comment
https://www.sau.com.au/forums/topic/136806-turbo-timer/#findComment-2544698
Share on other sites

i never let it sitting idle as you'll end up trapping a bit more heat due to no/less airflow.

exactly. letting it sit on the spot idling creates heat soak, which can raise the temp. if i fan it around close to home i usually just idle around the block to let it cool down.

Link to comment
https://www.sau.com.au/forums/topic/136806-turbo-timer/#findComment-2544858
Share on other sites

I dont have a TT...

...I just take it easy as im approaching my destination, and usually wait about 15-20 odd seconds (Usually spent closing windows, sunroof, side mirrors) before switching it off....but i never let it sitting idle as you'll end up trapping a bit more heat due to no/less airflow.

Ha? Can you elaborate? I live near a big hill and when I climb it my car usually sits around 2000-2500 RPM. So the turbo is working slightly and needs bit of cooling (20-50 secs) so I just idel in my drive way If i have time or walk off with TT on.

Link to comment
https://www.sau.com.au/forums/topic/136806-turbo-timer/#findComment-2544949
Share on other sites

I dont think anyone is saying a TT is harmfull champ!

Sir-D,

Im not sure what you want me to elaborate on? ...basically all im saying in my post is to take it easy as u approach ur destination and you wont really need a turbo timer.

And my personal opinion is that if you think a TT is gonna save ya then think again.

Thrashing your car then coming to a complete stop and leaving it on TT will NOT cool down the rest of your car like transmission etc...

Link to comment
https://www.sau.com.au/forums/topic/136806-turbo-timer/#findComment-2544976
Share on other sites

TTs are a bit of a wank, all that's needed is some common sense either drive gently and give it 10 seconds to idle before turning off or let it idle for 30-60 seconds and be done with it. Did this with my last car and never had a problem.

I do have a TT integrated with the alarm on my current car, this lets me be lazy and take the key out, get my stuff etc and then as I walk away I override the TT and turn the motor off then arm the alarm. Could count the number of times I've let it run the full 90 seconds (fixed) on one hand.

Link to comment
https://www.sau.com.au/forums/topic/136806-turbo-timer/#findComment-2545093
Share on other sites

I dont think anyone is saying a TT is harmfull champ!

Sir-D,

Im not sure what you want me to elaborate on? ...basically all im saying in my post is to take it easy as u approach ur destination and you wont really need a turbo timer.

And my personal opinion is that if you think a TT is gonna save ya then think again.

Thrashing your car then coming to a complete stop and leaving it on TT will NOT cool down the rest of your car like transmission etc...

But isnt that related to any car, turbo or not as far as cooling the tranny etc goes?

Link to comment
https://www.sau.com.au/forums/topic/136806-turbo-timer/#findComment-2545444
Share on other sites

From Wikipedia, the free encyclopedia

Jump to: navigation, search

A turbo timer is a device designed to keep an automotive engine running for a pre-specified period of time in order to automatically execute the cool-down period required to prevent premature turbo wear and failure. After a period of driving when a turbocharger has been working hard, it is important to let the engine run at idle speed for a period of time, allowing the compressor assembly to run down in speed and cool from the lower gas temperatures in both the exhaust and intake tracts. At the same time the lubricating oil from the engine is able to circulate properly so the turbine won't burn the lubricating oil that would otherwise be trapped within the charger with the turbine rotating at high speed.

http://en.wikipedia.org/wiki/Turbo_timer

Link to comment
https://www.sau.com.au/forums/topic/136806-turbo-timer/#findComment-2549478
Share on other sites

Ive seen on some TT's it says suitable for Turbo charged Vehicles and NA vehicles. I always go easy a few mins before reaching destination and give it a few secs when i pull up.

The shafts on most turbochargers spin in excess of 50,000 RPM and generate lots of heat. To keep your turbocharger's heat under control, most are cooled by circulating oil or water (coolant) around the shaft. The turbocharger's shaft is free to rotate at will and there is no way to stop the shaft from spinning after shutting the engine off. To dissipate and stabilze the heat in the turbocharger, most manufacturers recommend that a car be idled for a period of time after moderate to hard driving to allow the oil/water to take heat out of the turbocharger.

Failure to reduce the temperature of the turbo could result in the oil around the shaft "coking". Coking is basically the baking of oil, turning it into a hard substance that could plug your oil lines and cause oil "starvation", preventing proper cooling of your turbocharger and reducing it's operating lifespan.

Edited by 95SKY
Link to comment
https://www.sau.com.au/forums/topic/136806-turbo-timer/#findComment-2549516
Share on other sites

after moderate to hard driving to allow the oil/water to take heat out of the turbocharger.
After a period of driving when a turbocharger has been working hard

If you take it easy just before you reach your destination.. a turbo timer isnt needed..

anyone who thinks they can drive hard then shut off their car immediately is stupid.. turbo timer or not

Link to comment
https://www.sau.com.au/forums/topic/136806-turbo-timer/#findComment-2549844
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
×
×
  • Create New...