Jump to content
SAU Community

Recommended Posts

  • Replies 160
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

It's coming along nicely thanks!

Me and Nathan spent the whole day and night working on it... we got heaps done!!

JIC castor bars IN!!

Inner guards GONE!

S13 Steering rack IN!!

RB25 head OFF!!

We just have to sort out some new S13 rack ends (with longer threads to suit the magic washers), drilling and tapping a hole in the block for the turbo oil return line and the cometic head gasket (not quite sure on the thickness yet). >_<

Edited by RB_turbo_bitch
I thought the block would of had all the oil and water fittings already there, mine did, must of been lucky.

Have you decided on the comp ratio yet and what boost do you plan on running

You must be using the R32 RB25?? Mine is a R33 RB25.. and it has no turbo oil return line at all but inside the block you can see the indent where it is supposed to be..

We've decided to use the 2mm head gasket which should bring the comp. down to 8.4:1 ;)

A 2mm headgasket drops the comp by ~1 point over the std 1mm h/g.

So given the R33 Rb25DE is 10:1 (I think or is it slightly higher) that drops the comp to ~9:1. ;)

We are using a 1.8mm now so yep i am told it should be around that now.. still high comp but not too much higher than std rb25det comp..

Pics update

picture024rm0.jpg

picture035mx3.jpg

picture052mq0.jpg

picture057pc7.jpg

picture010pi5.jpg

;)

Edited by RB_turbo_bitch
  • 4 weeks later...
  • 2 weeks later...

This week me and Mark spent quite a bit of time degreasing EVERYTHING so it was all ready to go when the block was done.. we ended up deciding to rebuild the bottom end...

Yesterday we bought;

new piston ring set

timing belt

1.8mm thick 4 layer cometic head gasket

race series bearing set

conrod bearing set

RB25 power steering pump (non hicas)

I also sanded back the lower lip from my GTR front bar.. ready for repainting...

Today Cammo tapped and drilled the hole for turbo oil return line!!!

SO MONDAY IS THE DAY FOR ASSEMBLY!! :)

more pics....

picture159ba0.jpg

picture157fd8.jpg

picture170ig1.jpg

picture167ni7.jpg

:rofl1:

and yes it will be getting a tune ASAP.. hopefully in time for the Jan Drift Day in a few weeks at QR!!

Edited by RB_turbo_bitch

Today the bottom end rebuild was completed!

Tomorrow the head goes back on!!

I still have to buy a manual spigot bush (from nissan?)

and the non hicas power steering lines should be arriving thurs/fri..

So we should have it all up and running this weekend!! :glare:

50,000km's and no issues with my cometic. :)

THe motor still has the same compression as it did when it was new. >_< So.. Very happy as one would be. >_<

yea but yours is almost N/A Joel

pump some boost into her and see how she holds up! :)

yea but yours is almost N/A Joel

pump some boost into her and see how she holds up! :rant:

Its been running 1bar through the mid for some time now with my home bodgy tune. Just boost drops to 11psi odd by 4500rpm. :)

So 1bar from 2200rpm until 4500rpm.

Goes quite hard in the lower gears. Just 100km/h + it falls over.

Has no issues edging out a mates r32 rb30det gts4 gt35r making 270rwkw (17psi) through second gear on a rolling run, he passes in third once we are up over 120km/h. So the mid range is definitely not n/a like, just the top end. lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...