Jump to content
SAU Community

Recommended Posts

Hi, I have the Super Dragger on my R34 GTT. I have no issues with scraping and it sits up quite neatly under the bumper. From the side of the car you can just see the bottom part of the stainless steel muffler sitting under the bumper.

To install, it was quite easy, did it my self. It comes in two parts, first section is from the cat back, and is about 1.5 meters in length. It has a small silencer built in. The muffler section is about the same length and the two bolt together with 4 bolts and a gasket.

If you do go for the Super Dragger, be warned that the muffler is huge when sitting on your kitchen floor. I was amazed at the size of the thing. And in all fairness to HKS when its on the car its a really neat and small install.

The hardest thing with the install was getting the old exhaust off. Two bolts hold it to the cat and these usually have seen better days.

The sound from the exhaust has a bit of bass. not too much and this cools off when the exhaust warms up. From inside the car the exhaust is nice and quiet, and from outside gives a nice low sound.

If you stand beside the car and rev it, the engine is actually louder than exhaust.

Over all, its a very good purchase.

John

thanks for the reply John :ban:

do you mind if i ask where you got yours from? $? and any pics? :wave:

cheers mate..

p.s. yet to hear back from other guy selling his one?

i have one on gtr

no real problems with scraping , no more than any other exhaust on a lowered car

note is good power gains good

only problem is it hits the extra v-spec bracing but not really applicable for you

a r33 one will fit with only minor mods

i paid 300$ for mine , shouldnt be to hard to find one for a 33 2nd hand

thanks guys. Sounds great from the clip :) nice low rumble on idle :P

thanks for the R33 tip, i was wondering whether it would fit as i would imagine there are more 2nd hand R33 ones than R34.

and in regards to the one on sale (link at top of this page) when it says 'muffler', i still need another piece to connect to the cat? Could any exhaust place make this up for me? Or does that just make it totally different to a full HKS dragger catback?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...