Jump to content
SAU Community

Recommended Posts

Got one in mine as it came with it.

pros,

handle high HP

handle a shit load of abuse(high rpm launches)

last a long time still going after 5 years of use

well built and engineered

no slippage

con's

gearbox breaker (no spring dampers or give)

bitch in stop start traffic

I thought more torque loading etc that the clutch lets through (quad vs triple) would mean more stress on the gearbox (physics), unless it has damper springs etc to take up shockloading. Still punishing gearbox though.

OS GIKKEN STR twin sounds good.......

Yeah i thought the same thing, Kier wilson explained it to me and showed me the differance between the clutches. Somehow the quad plate puts less effort on the driveline than the triple. if indoubt feel free to give Willalls a call, they had the trpiples in both there GTR's and now run the quad's as they found them easier and more friendly to drive. YEs they are the OS distributers here in S.A and would try to make a slae off the quad rather than the triple but i got the quad at the same price.

Fair enough, main thing is as long as you are happy with it, go with it.

I'm happy with my os triple as it has lasted so long (daily driver, 380ish RWHP) and only one busted g box so far, 3rd gear.

well the number of plates has very little bearing on driveability at all.

two equal clutches. both puck type. both metallic friction material. both same pressure plate. both solid centre. one is a tripple, one is a quad. I can tell you now they will both be the same to drive.

things that affect driveability of a clutch:

force of pressure plate

type of friction material used

style of plate (full face, puck type etc)

sprung/dampened centre

saying a quad plate is easier to drive than a tripple is still a useless statement. there are hundreds of types of each clutch. if I had a sprung centre, full faced, 1000kg pressure plate tripple plate. and on your advice that a quad plate will be better went and bought one. and it was solid centre, puck style plate, 1600kg pressure plate which do you think would be easier to drive? and kinder on the gearbox?

exactly. :) my point is. saying quads are better than tripples for driveability is not acurate. of all the factors in clutch design it probably has the least impact on driveability. and yes I've driven plenty of singles, quite a few twins, a number of triples and a couple of quads. I had an OS tripple in my GTR for over a year, and an OS twin in it for about a year.

so you guys wouldn't recommend a triple plate for daily driving? What power will a streetable twin plate hold up?

I converted my solid centre HKS twin plate to a sprung centre. Absolutely transformed the car (was a bitch to drive previously in stop start traffic) and seems to be surviving 400 rwkw abuse OK.

yep, massive difference between solid/sprung centre clutches.

and ookami, like i said, it depends on the type of tripple we are talking about.

if you are talking OS solid centre, puck style, tripple then no, it's no good for daily driving. if you are talking full face, sprung centre tripple, with a not too extreme clamp force then yes, it should be fine for street use.

Just get Jim to make you a clutch if your worried.

Tough as nails, great for street driving

best advice anyone could give you....

i daily drive my GTR, jim berry built mine.. it is a single plate button with a carbonics plate.. bites HARD.

and considering he built it cheaper than what a stock replacement costs... can't go wrong

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...