Jump to content
SAU Community

Recommended Posts

I have a 1999 R34 GT (manual) RB25DE

Put out 101.8 kW fully stock then put on a full Trust stainless steel catback exhaust with 80mm tubing and 115mm tip, and a full cold air intake kit (with a Trust Airinx pod filter), did another power run and the car jumped up to 118.7 kW. I thought that wasnt too bad really!!!!

Edited by MissR34
  • 3 weeks later...

1997 R33 GTS25 series 2

I just got the 33 dynoed on the weekend. Came out with 160hp/116KW at the rear wheels. Engine is completly stock, Only with cat back exhaust.

Also: My mechanic pointed out to me that it has a set of nismo racing struts on it as well, They were already on the car = win!

Edited by OBNXSH
  • 2 weeks later...

new power figure

dyno dynamics

modifications: standard panel filter, coby extractors, 2.5" cat and 2.5" cat back exhaust, matty spry tuned safc2

power: 115.4rwkw

consensus: panel filter and an intake idea and i'd be done. wouldn't recommend going any further with power mods, despite the coolness of cams, cam gears, port and polish - costs would be astronomical for minimal gains, you would also be looking into a proper ecu to make the full use of them. extractors dont give any sort of peak power, but driveability and fatter mid range is very noticeable. with the retune reving is much smoother, power delivery is nice and "free", definitely a much better car to drive. peak power is only a number.

future mods: would stick to drivetrain mods; lightened flywheel, shorter diff ratio, lighter tail shaft - try to make the current power more useable.

does it have to be skyline...... 98 3.5 v6 Mitsubishi verada (4 speed slush box auto) with pacemaker extractors, lukey muffler mandrel bent 2.5 inch system + unichip = 130fwkw

  • Like 1

my r34 gt is now doing 119.9kW at rear wheels. just got extractors put on so going back in a couple of weeks (to allow ecu/sensors to adjust and do its funky thing). my car can now breathe!!!!!

Model: 1987 R31 Skyline Ti

Engine: RB30DE with VVT

Modifications: Extractors, exhaust, twin tb, safc untuned, billet f/wheel, reground surecams, 10.5 compression, 18 degrees timing, 98ron ultimate

Power: 150.9RWKW @ 172kmph an 507nm (374FtLb) torque at 144kmph

with more left in it, she's an economical daily but rich and restricted above 5000rpm so once thats tuned/fixed i'll be a happy camper

I built this engine and ran it in my 86 r31 Skyline station wagon . With a 4.11 locked diff , 195,60x14 radials @ 20psi , i recorded a best 1/4 mile of 14.15 @ 97.6 mph at Willowbank dragstrip 16-8-2006 .

Also at Lake Gairdner speed trials 2006 ,max speed of 141.18 mph ( 227kmh ) using 3.7 diif with .75 OD . ( had fuel starvation prob )

Well after yesterday.....

Model: 2000 R34 GTV Manual

Engine: RB25DE NEO

Good Mods: Fujitsubo Cat Back ( 70mm pipe ) - APEXi Panel Filter

Bad Mods: Starcorp Impul 18's w/275/35/18 ( fcuking heavy )

Power: 107.7rwkw

  • 5 weeks later...
Model: Z33 manual

Engine: VQ35DE

Mods: 2.5" catback exhaust (not entirely dual), intake manifold spacer, pod filter, Unichip

Power: 189.2rwkW

Mods: Above + extractors, high flow cats, modified intake plenum runners, increased redline, retuned Unichip

Power: 195rwkW

R31 Silhouette

RB30E Manual

S1 Cam, Powerchip, Extractors, 2.25" Exhaust with one muffler, no silencer, Hi Flow Cat

Heavy Duty Clutch, R33 Airbox with sealed cold air intake, LSD.

117rwkw 14.2 0-400m

Citroen Xsara VTS 2004 2.0lt XU10J4RS

Hi Flow sealed air intake, Tuned Mandrel Exhaust 2.25", Chip

114fwkw 15.0 0-400m

  • 1 month later...

Car: Aussie R31 GX

Engine: RB30e internally standard ie. standard head & cam

Trans: factory 5 speed

Mods: XF Falcon TB, 3" mandrel bent intake pipe with K&N pod, raising rate fuel pressure reg, extractors, 2.5" straight through exhaust with very high flow cat, advanced timing, 10mm leads, Exedy clutch & minispool.

Power: 108rwkw on a Dyno Dynamics dyno

Carl

  • 3 months later...
  • 1 month later...
  • 2 weeks later...

pulled 115.6rwkw with a fuel problem.

need a new pump and change of fuel filter.

should be able to hit 120 with a bit of timing advance as well.

dynodynamics dyno @ unigroup engineering.

5zigen 2.5" catback exhaust & K&N Ms pod filter.

Edited by whyte

interesting figures,,,

for the record mine was totaly stock at 200.9hp (149kw)at flywheel and 140hp 104kw.@wheels(6500revs)

with 150lbft torque @ 5400 revs

from the comparisons on here and given that was stock with new plugs, thats quite high suprisingly.

Edited by Hesh
  • 2 weeks later...

I know its not a nissan and not a skyline.... (i'm on here looking for power figures of NA 6's... actually in the market for a 350Z to modify NA style...)

My N/A BA XR6 Falcon puts out 194.3rwkw... @ 6800rpm

(192rwkw @ 5800rpm)

Currently has -

Nizpro CAMS

CAPA flash tune (by Nizpro)

Custom Twin Throttle Body setup (2x 70mm TB's)

Nizpro Custom Extractors

BF Turbo Exhaust

to Come -

Compression increase from 9.65 > 10.4

Intake manifold Phenolic Spacer

Individual Throttle Bodies (6x 45mm)

Port and polish

Custom Zorst with twin 2.25" metal cats

Retune...

for those who don't care about the falcons but are curious, the Barra 182 Engine stock is a 4.0L inline 6 with 182 Fly wheel kilowatts.

How much should I expect from similar mods on a VQ35DE?

Cheers

Edited by Guardian_aiur

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
×
×
  • Create New...