Jump to content
SAU Community

Recommended Posts

Not sure if this is the right place to put this but..

Ive read somewhere that petrol loses its OCTANE level after a period of time.

So approx how long does this occur? Is this true?

For example I fill up the car with BP Ultimate 98RON, how long will it take to "expire" and lose its "98RON" properties?

Is it bad for the car if there is fuel in the tank from like say 6 months ago?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/138836-petrol-expire/
Share on other sites

I'd leave fuel in the tank, an empty tank tends to rust.

And some light reading on the subject:

http://www.chevron.com/products/prodserv/f...detecting.shtml

http://www.virginiawind.com/tips/gasoline_stabilizer.asp

http://www.challengers101.com/FuelStorage.html

The last one is the most generally informative. I was looking for a deterioration duration curve [time vs decay] but couldn't find one.

Link to comment
https://www.sau.com.au/forums/topic/138836-petrol-expire/#findComment-2585746
Share on other sites

less wh0ring more explaining.

maybe around two weeks it would drop a bit of its just sitting there in the tank?

Hmm interesting.. thanks Paul! :)

Mate works at an Audi workshop, they had a car sitting for 2 years and someone tried to start it. The petrol had thickened and needed new lines and pump as they were all clogged up.

lawl two years

Link to comment
https://www.sau.com.au/forums/topic/138836-petrol-expire/#findComment-2586284
Share on other sites

a friend who used to run a local servo a few years back said it drops octane even while sitting in the tanks at the servo. so servos that dont do as many customers, fill up less often, are likely to have lower octane fuel than a busy store than fills up reguarly

Link to comment
https://www.sau.com.au/forums/topic/138836-petrol-expire/#findComment-2586327
Share on other sites

Official word from Shell is that their fuel will be stable if stored up to one year, as long as the storage conditions are "adequate" - ie the containers are full to minimise exposure to air, tightly capped, out of direct sunlight, and under 27°C.

underground tanks at servos don't even fulfil those requirements. And vented petrol tanks in cars that get nice and hot sitting in the sun and cool down again at night certainly don't, so the fuel deteriorates much faster than these optimum storage conditions in Shell's literature.

Link to comment
https://www.sau.com.au/forums/topic/138836-petrol-expire/#findComment-2586384
Share on other sites

The deterioration of fuel is or can be brand dependent. If you read any of the links in my previous reply, it appears that the length fuel can be stored also relies on the preservatives each company uses to increase the shelf life of their brand. I don't know which ones are best, but I wouldn't trust any of them. Its an easy question really: Whats cheapest, a new tank of fuel or an engine rebuild?

Link to comment
https://www.sau.com.au/forums/topic/138836-petrol-expire/#findComment-2586431
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...