Jump to content
SAU Community

Recommended Posts

mmm

gf rekons fresh coat of black with some rainbow flake in it

im tossing up gunmetallic grey with heavy rainbow flake... or my gfs mazda chocolate metallic brown (still have 2L of paint left from her car so...)

front wheelbearings i believe are my noise/vibration in the front so need to get them done this week

just need to wait till tomorrow to ring around for bearing prices

front 18's arrive this week to complete the set (yay)

however my gf just bought some 18x9 +15 and 18x9.5 +12 bronze TE37's... and she wants my wheels so... im unsure wether to swap her or not...

18x10.5 +26 with 8mm floater and -1 camber with 215/40/r18 stretched

guard rolling done by my gf

guards getting fixed in about 2 months and being pulled out another 10-20mm... ideally i want to run 18x9 +0 front and 18x10 +0 rear comfortably i can fit an 18x10 +10 without spacer with the lip of the rim exposed by guard edge (what i consider flush)

LOL

dude i got about 30mm of pull so far

factory untouched guards you can roll on 9jj +30's all round with some stretch... ceffies dont accomodate shit

do i have pull? oh i got pull! it aint pretty but its pull!

post-25224-1170938380.jpg

man i wish my girlfriend had similar .. or even remote interest in cars and taste in wheels with offsets like that.

tuff looking ceffy though dude.... ur always turning out DISH on your cars.. im jealous.

good luck with it.

well i test fit te37s tomorrow... oh yesh pics will be supplied :no:

both on her s15 and on my a31... so... d day tomorrow

kinda turned off by dish... although later on this year ill be getting an s14 shell to do as a long term track project... looking to squeez 18x11 -20 under the rears :P or something like that

**WARNING** NO 1" POLISHED LIP CLASSIFIED AS DISH QUOTED WITHIN BY THIS USER

Edited by Hella Flush
LOL

dude i got about 30mm of pull so far

factory untouched guards you can roll on 9jj +30's all round with some stretch... ceffies dont accomodate shit

do i have pull? oh i got pull! it aint pretty but its pull!

:( wats da measurements of dat rim in dat pic in da rear guards?

in the bottom one? LOL

16x7.5 +45 hahahaha

SUNKEN TO THE MAX

my 10.5 +26's are much better fitting but still in a tiny bit

haha yea ... sunken!!!! :happy: ...lol

Edited by Dan_J
  • 2 weeks later...
  • 8 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
×
×
  • Create New...